Search:

Type: Posts; User: Gordon Seto; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.24 seconds.

  1. Replies
    24
    Views
    32,395

    Bernie, the sad part was you are not alone. 10...

    Bernie, the sad part was you are not alone. 10 or so Creekers who had that lathe all reported to have multiple problems.
    I think Woodcraft has the new Rikon Variable Speed for $280 on Black Friday...
  2. Replies
    15
    Views
    3,907

    I have the SG; it cuts fast, runs cool and holds...

    I have the SG; it cuts fast, runs cool and holds up well.

    I also had the Norton 3X "I", didn't like it and returned it. It was too soft for HSS turning tools; it didn't hold up. The wheel...
  3. Replies
    24
    Views
    32,395

    [QUOTE=Bill Bulloch;1555335] 50 Craftmen Lathes...

    [QUOTE=Bill Bulloch;1555335] 50 Craftmen Lathes for sale ... but a 2HP, 15" swing lathe is a nice lathe to start out with. [QUOTE]


    Be careful. Ask Bernie. You don't want the model private...
  4. Replies
    24
    Views
    32,395

    Don't rush into buying the chuck yet. It is a...

    Don't rush into buying the chuck yet. It is a convenience item. Even you have several chucks and jaws, you still need to use the alternate methods, such as glue blocks, jam chucks. Learn to use...
  5. Replies
    24
    Views
    32,395

    Don't overlook the major advantage of the 1220VS...

    Don't overlook the major advantage of the 1220VS (not the 1014 VS) is its minimum rpm of 200 instead of 500 on the manual speed model. The slower rpm would allow you to safely turn slightly...
  6. Replies
    30
    Views
    3,888

    With fastfood value meal already at $5, $100 per...

    With fastfood value meal already at $5, $100 per day with lunch provided is a bargain.

    But I think that has to do with location, location & location. There are 3 main competitors:

    Commercial...
  7. We are turning wood here. They don't have...

    We are turning wood here. They don't have uniform density. Moisture distrubution would affect the balance of the blank. The best tachometer is your gut feeling. If the lathe shakes, or you feel...
  8. From this chart in Tormek manual:...

    From this chart in Tormek manual:
    http://i118.photobucket.com/albums/o83/gbseto/TormekSVD-185copy.jpg
    It has the same principle as Varigrind. The JS setting is equivalent to the leg angle setting,...
  9. Replies
    18
    Views
    7,009

    In addition to that, we baby our hand plane...

    In addition to that, we baby our hand plane blades. We pride taking paper thin shavings off hand plane. We never use our good plane blade on timber with bark or dirt.

    Turners are different...
  10. Replies
    18
    Views
    7,009

    According to this tool steel selection chart:...

    According to this tool steel selection chart:
    http://www.crucibleservice.com/eselector/prodbyapp/highspeed/highspeedchemtbl.html
    M42 has very high "red hardness" which is desirable in metal...
  11. +1 on what Dale said. Have "seen" it twice at...

    +1 on what Dale said.
    Have "seen" it twice at Woodcraft open turn night- a loud bang, big chunks of the wheel missing. It happened so fast, not even the guy knew what happened. Jamming the blunt...
  12. Replies
    3
    Views
    12,674

    This is not a chuck for wood turning. The 3...

    This is not a chuck for wood turning. The 3 contact area are too small to hold the blank securely; the concentrated force would crush the wood. This kind of jaws can be a knuckle buster.
    Look for...
  13. Replies
    12
    Views
    3,475

    http://www.woodturners.org/tech_tips/vacuum_chuck/...

    http://www.woodturners.org/tech_tips/vacuum_chuck/vacuum-chucks.pdf
    (Pages 4 & 5) explains what you want to know. If your system is not leaking (poor seal, thin wall, porous wood), probably you...
  14. Replies
    9
    Views
    1,021

    BTW, if you over-tighten, the tail stock live...

    BTW, if you over-tighten, the tail stock live center also gets hot.
  15. Replies
    9
    Views
    1,021

    Crank it tight, then back off very slightly. The...

    Crank it tight, then back off very slightly. The amount is so small, it is mostly by feel. It will get loose during turning. Stop, check and tighten if you need to.
  16. Replies
    10
    Views
    2,431

    That is very common. Switch to Satellite...

    That is very common.

    Switch to Satellite radio, try plugging in the radio from different electrical outlet or install something similar to this.
    http://oneway.ca/lathes/2436_access.htm
    RFI...
  17. Replies
    9
    Views
    1,021

    Is the headstock also getting warm without load? ...

    Is the headstock also getting warm without load? Cranking the tail stock too tight can cause the bearings to heat up.
  18. Replies
    29
    Views
    12,114

    That is what the swiveling headstock is for. If...

    That is what the swiveling headstock is for. If you don't need the tail stock, just swivel the headstock a little, no more bending forward in hollowing.
    This alignment tool would bring back the...
  19. Replies
    16
    Views
    3,928

    He claimed to be 14, from UK. Quote from his...

    He claimed to be 14, from UK. Quote from his YouTube Profile:
    "I do not believe that you need to have any formal training to learn woodwork, afterall I havn't."

    I am glad he doesn't have the...
  20. Replies
    16
    Views
    3,928

    Moving the tool rest while the lathe was on was...

    Moving the tool rest while the lathe was on was the tame part. IMO, it is crazy to stick the fingers inside the vase to sand as he started at 7:10...
  21. Replies
    10
    Views
    1,405

    No problem with Lightning Publications. They...

    No problem with Lightning Publications. They arrived nicely in plastic bags.
    It used to be fifty something dollars a year. I know a guy put his past Woodturning magazines at the auction site. ...
  22. Replies
    5
    Views
    1,441

    The belt tension may be too tight. According to...

    The belt tension may be too tight. According to the Jet service, that was also the main reason for pre-mature bearings failure. Don't put too much force pushing down on the motor bracket to tension...
  23. Replies
    11
    Views
    2,123

    From your post, it gives me the impression that...

    From your post, it gives me the impression that upgrading your lathe may be in your future.
    If that's the case, I would suggest you consider a chuck that is not direct threaded (such as G3 or SN2). ...
  24. Replies
    8
    Views
    12,711

    The T-124 has 16.5" swing. At 570 rpm, the...

    The T-124 has 16.5" swing. At 570 rpm, the peripheral speed is 27.99 Miles per Hour. It is still too fast even for a rounded & balanced bowl of that size.

    Looking at the picture, the headstock...
  25. Replies
    34
    Views
    7,299

    No tool can make a better turner. You are going...

    No tool can make a better turner. You are going to hold the tool free hand. With a fingernail grind bowl gouge, using various parts of the edge, push or pull cuts, scraping or shear scraping;...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4