Search:

http://images.craigslist.org/00A0A_4RFwVE7F31h_600x450.jpg

JET Gold Cylinder sander like new whit a lot of extra for fast sale $795 retail for $2500 for more info. please call me

Not mine, just...

I find myself in need of more sandpaper, and found some Mirka paper sheets on closeout (50 sheets of 150 grit for $9). Are their abrasives any good?

Some knife makers forge them into knives, too.

bump bump.

The filters can just get gunked up with garbage over time too. I recently replaced the one in my BR320 blower. The blower would idle fine, but when I opened the throttle it would rev, then try to...

A used Laguna 16HD has shown up on my local Craig's list. From the equipment plate, it was built in 2007, and from the pictures, it looks like it has been well cared for/very little use/very good...

Ok all, apparently a composite picture. Guy is still not the sharpest tool in the shed ripping without his fence.

...

Heh.

You're the winner.

Posted on another forum I read (firearm related). Guys started talking about TS's, and this fellow posted this picture:

http://i44.tinypic.com/1z4elgn.jpg


Edit: Thread still developing...may...

My old dewalt dw705 is nearing its life expectancy after about 12 years and lots of lumber.

I see that HD is going to have their 12" scms for $400 on Black Friday. Any thoughts, opinions or...

I've been trolling my CL's for months looking for a larger BS with no luck. You suck! ;)

So it turns out patience pays off. About a month ago, a guy advertised some purpleheart on my local Craig's list. I sent Hume a message, asking how much. He quoted me $17/ board foot. There is a...

Keep an eye amazon. I had 4-40 inch bessey revos delivered to my door on Thursday. $107, after they got done collecting taxes. They are VERY nice clamps. Almost afraid to get glue on them.

I know..it was a joke. Sorry!

I'm replacing the standard knives in my Grizzly planer for the Self set system. Excluding the cost of the blade holders, for a difference of about $8, I can have a factory edge each time I need new...

How do you use that tape measure with no 1/8 or 1/16th inch graduations? ;)

My two sets of 40's (missed the 24's) should be here next week. Looking forward to them.

I had always used cheap clamps until a couple of months ago. A fellow creeker was getting out of the...

Explain the canted blade angle, please. How does that effect quarter sawing?

Couple of thoughts...if you can wait, check out arborsite.com. It's a chainsaw based forestry forum, and some of the guys over there build and race chainsaws. They cut cookies for fun, and if someone...

Thanks everyone for the replies to the thread. Jack, I loved the pictures. It amazes me what people were able to accomplish when everything was mechanical. There were some truly brilliant people...

I've had a request for an end grain cutting board similar to this:

269613

How would you go about machining the depression/portion of the sphere? FWIW, I don't have a lathe and the board would...

My rendition of the wood whisperer's cutting board. Still need to sand it and give it some SBF.

http://i44.tinypic.com/16ih5k4.jpg



http://i39.tinypic.com/2zefias.jpg

Thanks everyone for the replies. It seems the general consensus is mahogany of some flavor, and from my reading, it is less than ideal for cutting boards. I have some purpleheart and some thicker...

I was digging around in the odds and ends box, and found an 8/4 piece of whatever this is, about 18" long. It was given to me a while back, and I thought it was cherry, but seems too dark now that...

Red oak and white oak have almost identical hardnesses, and red is generally cheaper, at least here in the southeast.

OP, I'd check out the "materials" section of your local CL. I have seen lots...