Search:

Type: Posts; User: Dane Riley; Keyword(s):

Page 1 of 5 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    19
    Views
    3,206

    If you start your saw with the tension releases,...

    If you start your saw with the tension releases, it will usually ruin the blade.
  2. Replies
    5
    Views
    1,559

    I've replace spatula handles with turned walnut...

    I've replace spatula handles with turned walnut finished with walnut oil. These have been through the dishwasher hundreds of times. They get dull, but reapply walnut oil and they look like new. And...
  3. Replies
    12
    Views
    3,305

    And that's with a Monroe hollower.

    And that's with a Monroe hollower.
  4. Replies
    12
    Views
    3,305

    Deep hollowing with and armbrace is a good way to...

    Deep hollowing with and armbrace is a good way to dislocate your shoulder. I came close. I won't use my armbrace for long over the tool rest or with a curved tool. You need a captive hollowing system.
  5. Replies
    12
    Views
    2,312

    The O rings are snug. I do have a holder to hold...

    The O rings are snug. I do have a holder to hold the hose and provide a bit of pressure to keep it from falling out.
  6. Replies
    12
    Views
    2,312

    Second this. I made mine with a brass fitting and...

    Second this. I made mine with a brass fitting and cut some groves for O rings392235
  7. Replies
    9
    Views
    2,131

    You need a bleed valve to position the turning...

    You need a bleed valve to position the turning and a gauge to set the bleed valve. A filter is a good idea to prevent dust from being sucked into the pump.
  8. John, next time you photograph in your shop,...

    John, next time you photograph in your shop, could you photograph your spindle gouge grinds and start a new thread? I know what a many versions of a bowl gouge grind looks like, but have seen few...
  9. Replies
    53
    Views
    9,175

    My cross feed drill vise had way to much play to...

    My cross feed drill vise had way to much play to work for threading. When I saw this video I tried to readjust mine. One axis was fine already, the other one would not turn with a reasonable amount...
  10. Replies
    6
    Views
    1,427

    Some of the prettiest of turnings come from the...

    Some of the prettiest of turnings come from the ugliest of logs. And that log is ugly.

    This looks good for a tall hollowform.
  11. Replies
    53
    Views
    9,175

    I have a piece of aluminum that sits between the...

    I have a piece of aluminum that sits between the bed ways. This maintains the Y axis position and the square alignment. Notice the twist mark that reminds me which way to take up the small amount of...
  12. Replies
    53
    Views
    9,175

    Yes. It was so tall I needed the steadyrest,...

    Yes. It was so tall I needed the steadyrest, usually I don't.

    The Y slide is some sort of extrusion I found at the local scrapyard. I lock it with the screws at all four corners. I went to a lot...
  13. Replies
    53
    Views
    9,175

    ok 390462390463390464

    ok

    390462390463390464
  14. Replies
    53
    Views
    9,175

    It is 1.25 x 8, so the chuck threads directly on....

    It is 1.25 x 8, so the chuck threads directly on. When Enco was around it was not expensive with a 20%o ff and free shipping. That may be why they got bought out.

    The wood blocks with screws that...
  15. Replies
    53
    Views
    9,175

    There can't be any play anywhere. I suspect you...

    There can't be any play anywhere. I suspect you will need to lock the dovetail with locking screws tapped in the sides.390381

    The play on the threaded rod must also be eliminated. Mine has...
  16. Replies
    44
    Views
    7,032

    I fit that, and I'm in Forestville This weekend...

    I fit that, and I'm in Forestville This weekend is out, but next week is possible.
    If you go to Wine country Woodturners, You've seen if not talked to me. I'm bad with names in my old age. Hard...
  17. Tool rest height is also involved. If the spindle...

    Tool rest height is also involved. If the spindle height is higher, try dropping the tool rest slightly (in relation to the spindle) so the tool is not level but the handle is lower. The cutting...
  18. Replies
    6
    Views
    2,669

    One thing I've wondered about is if the alignment...

    One thing I've wondered about is if the alignment is off is it because the tailstock is cocked(skewed) or offset? It could line up perfectly if the two errors were opposite. One way to check for this...
  19. Replies
    7
    Views
    1,587

    A PVC "T" for sprinkler risers (side hole is NPT...

    A PVC "T" for sprinkler risers (side hole is NPT threaded) stuffed with cotton works well.
  20. All my large apple trees are hollow. Some just...

    All my large apple trees are hollow. Some just have crescent shaped trunks. Still produce lots of apples.
  21. Replies
    14
    Views
    2,175

    Huh? You don't change jaws? Or does the non...

    Huh? You don't change jaws? Or does the non permanent locktite release easily?
  22. Replies
    8
    Views
    3,041

    369987Largest Diameter .85" 7 teeth 30 deg...

    369987Largest Diameter .85"
    7 teeth
    30 deg angle where engages.
    13 Deg on upper part

    $50 for no chuck key and no jaws is a ripoff, IMHO. That said, I like the chuck, although the precision is...
  23. Replies
    6
    Views
    2,029

    Not rolling, but could easily be made so. ...

    Not rolling, but could easily be made so.

    4(Qty.) 1.5" x 1.5" x 17" legs with 3 notches cut in each leg. 3(Qty.) .75" x 11.5" x 18" , each with a 3/4" deep and 1.5" wide notch on each side,...
  24. Replies
    12
    Views
    7,168

    Denatured alcohol dissolves wax. I would think...

    Denatured alcohol dissolves wax. I would think you could remove enough with this to allow adhesion of another finish. Anyone ever tried this? How much did you have to wipe it to get adhesion?
  25. Replies
    12
    Views
    7,168

    Could you enlighten us on how to "sun treat"...

    Could you enlighten us on how to "sun treat" flaxseed oil?
Results 1 to 25 of 107
Page 1 of 5 1 2 3 4