Search:

Type: Posts; User: Peter Froh; Keyword(s):

Page 1 of 5 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    64
    Views
    6,751

    I’ve had a Fitbit. It broke. I’ve had a...

    I’ve had a Fitbit. It broke.

    I’ve had a garmin, it broke.

    I’ve been wearing my Apple Watch for years and it’s been tough enough to not break.
  2. You will lose soft start but you can disable the...

    You will lose soft start but you can disable the speed control. I had to do that when I attached a Super PID to mine.

    406680
  3. Replies
    12
    Views
    1,882

    Maybe just the illusion of sharp points. Cut out...

    Maybe just the illusion of sharp points. Cut out the shape then do a final pass with a vbit cutting the outline of the shape to make the surface look sharp.
  4. Replies
    7
    Views
    1,740

    Well I have it a shot and it worked ok. A few...

    Well I have it a shot and it worked ok. A few corners where depth was tiny there is some chip out.

    389400389401
  5. Replies
    7
    Views
    1,740

    Thanks guys. The board was finished almost a...

    Thanks guys. The board was finished almost a year ago but I’m afraid that the oil penetrated pretty deep.

    Might using epoxy work?

    Due to time constraints I can’t put a new one together for her.
  6. Replies
    7
    Views
    1,740

    Glueing Dilema

    I have a finished walnut end grain cutting board. Multiple coats of mineral oil and top coated with beeswax/mineral oil.

    I’ve created a maple end grain blank.

    I want to vcarve some some...
  7. Replies
    9
    Views
    11,528

    I have the Fuji HVLP mini mite 4 and love it. I...

    I have the Fuji HVLP mini mite 4 and love it. I added the 3M PPS system and will never go back to gravity or syphon fed again.

    I've been thinking of selling my Fuji HVLP system and getting one of...
  8. Replies
    49
    Views
    7,858

    I put 2 - 2x4 on edge through the bed, raised the...

    I put 2 - 2x4 on edge through the bed, raised the bed so that the 2x4s were trapped then had friends help me lift it off my trailer and into my shop. Very slick and lots board to hold for...
  9. Replies
    12
    Views
    6,241

    You could use one of these: ...

    You could use one of these: http://www.vhipe.com/product-private/SuperPID-Products-and-Accessories.htm
  10. Replies
    26
    Views
    6,404

    What's the URL of the new forum? I can't find it.

    What's the URL of the new forum? I can't find it.
  11. Replies
    21
    Views
    5,374

    I cut a hole on the top and screwed a 6" hvac...

    I cut a hole on the top and screwed a 6" hvac boot to it. Dust collection is not an issue anymore. I also converted mine to hook and loop paper.
  12. Replies
    9
    Views
    4,868

    Best of both worlds!! ...

    Best of both worlds!!

    http://www.fujispray.com/compressor-spray-guns/

    Here is a quick review from a member of a Canadian woodworking forum....
  13. Replies
    37
    Views
    8,255

    Congrats Alan! I bought one a while ago and it...

    Congrats Alan! I bought one a while ago and it works great with my Freud lock miter bits!!
  14. Replies
    20
    Views
    5,112

    Depth of Cut. Maybe I'll have to have a closer...

    Depth of Cut.

    Maybe I'll have to have a closer look at it and see if there is some adjustment screw loose.
  15. Replies
    20
    Views
    5,112

    Maybe I have an older model of the BD lift but to...

    Maybe I have an older model of the BD lift but to lock its position there is an under table handle that you turn to push a set screw against one of the lift's posts. I find that no matter how hard I...
  16. Replies
    20
    Views
    5,112

    I've had one for years and I really like it. It...

    I've had one for years and I really like it. It currently has a benchdog lift in it but I'm not happy with the mechanics of the locking function. I'm considering getting the Jessem lift that will...
  17. Replies
    8
    Views
    3,451

    Thanks Tony. I think the benchtop pro I just...

    Thanks Tony. I think the benchtop pro I just bought used will work for my small shop. Just not enough room for something 60" long.
  18. Replies
    8
    Views
    3,451

    I have a line on a used 2015 model of the CNC...

    I have a line on a used 2015 model of the CNC router parts benchtop pro. It's $5,500 Canadian which is around $4000 USD. But comes with a few toolings and a 1617 router. A similar setup from CNcrp...
  19. Replies
    8
    Views
    3,451

    What are the dimensions of your 2448 standard...

    What are the dimensions of your 2448 standard machine Tony? Trying to figure out if I can squeeze it into my one car garage shop.
  20. Replies
    8
    Views
    3,451

    CNCRP Benchtop Standard experience

    I noticed that the images for the Benchtop standard in CNCRPs is different than some YouTube videos on the Internet, specifically the z gantry (correct term?).

    Has anyone recently purchased one of...
  21. Replies
    10
    Views
    3,872

    Thanks for taking the time Keith. It's all new...

    Thanks for taking the time Keith. It's all new to me so I expect a learning curve. I have some background in design software, just not CAD/CAM, but I expect it will take some time to learn this...
  22. Replies
    10
    Views
    3,872

    Thanks Keith. I have to be mindful of my budget....

    Thanks Keith. I have to be mindful of my budget. I can't justify the $8000 price tag for a more robust system. It would be different if I was looking for something more production quality. I'll...
  23. Replies
    10
    Views
    3,872

    Thanks William. I do like the communities at...

    Thanks William. I do like the communities at both X-Carve and Shapeoko. They seem very helpful and the forums are a great resource. I've seen you post there once or twice ;)

    I don't think the...
  24. Replies
    10
    Views
    3,872

    Advice on CNC Router

    I'm thinking of investing in a hobby CNC router. I was looking at the large X-Carve and Shapeoko 3 XXL. I would prefer to find something more local and I came across 3D Tech Works out of...
  25. Replies
    3
    Views
    1,216

    Depending on the size of your CNC, maybe consider...

    Depending on the size of your CNC, maybe consider making an enclosure for your CNC and hook the dust collection up to that enclosure.
Results 1 to 25 of 105
Page 1 of 5 1 2 3 4