Search:

Type: Posts; User: Shane Black; Keyword(s):

Search: Search took 0.00 seconds.

  1. Thanks for the help everyone. Here is what I...

    Thanks for the help everyone. Here is what I ended up with for now. Much better I think. Could be improved but good for this. Sorry for the Flash. Ended up running this at 40 power 75 speed. picture...
  2. Here is the original image and a better photo of...

    Here is the original image and a better photo of the granite. Sorry the other one was taken with my phone. The original picture's dpi is very low I see. I did not check that before. I tried to...
  3. What to do to make this better? Photo on Granite.

    What is your opinion on this photo? This was my first try at granite. I wish it had better detail in the picture. I have searched the forums and looked a the Youtube videos on how to change the...
  4. Thread: 18" vs 24"

    by Shane Black
    Replies
    10
    Views
    1,229

    I have an Epilog mini 24. It has a 12" x 24" bed...

    I have an Epilog mini 24. It has a 12" x 24" bed in it. This has done most projects but I have had to turn down several because it is not large enough. So I figure I would get the biggest and most...
  5. Replies
    8
    Views
    1,592

    The turkey was inverted and looked the worst. I...

    The turkey was inverted and looked the worst. I tried it at 400 dpi 50 speed and 100 power. The geese I did not invert in this sample. those I tried at 600 dpi and 60 speed and 100 power. I will...
  6. Replies
    8
    Views
    1,592

    Better detail on Wood

    How can I get a better photo? I am using an Epilog mini24 40 watt.
    600 dpi on Baltic birch. Is it the wood I am using?204925204923204924204922
  7. Replies
    4
    Views
    1,691

    Do I need to mask it if I engrave the back?

    Do I need to mask it if I engrave the back?
  8. Replies
    4
    Views
    1,691

    Engraving Mirrored acrylic

    I am cutting and engraving mirrored acrylic. Do I need to mask it? Should I engrave on the back side or front or is this just personal preference. http://www.sawmillcreek.org/images/icons/icon5.png
  9. Replies
    12
    Views
    2,592

    I would rather have my fingers than worry about...

    I would rather have my fingers than worry about the blade!! Thousands on hospital bills or hundreds on blade and brake? Tough question!
  10. I would use 3\4" thick stiles and rails and...

    I would use 3\4" thick stiles and rails and backcut the panel to just under 1\4". Then cut a 1\4" slot in the stiles and rails. If cut right the back of the panel should still look good.
  11. You could cut the plywood thinner on the back...

    You could cut the plywood thinner on the back side with a dado blade. (just the part the goes into the groove) This way you get the same look without compromising much strength.
  12. Replies
    12
    Views
    2,592

    SawStop is great but it destroys the blade and...

    SawStop is great but it destroys the blade and the brake. You have to replace it if something happens. It stops in 5 milliseconds.
    Whirlwind you can use on any saw but you are limited on the type...
  13. Replies
    1
    Views
    932

    Corel X5 help

    I am making a world map out of acrylic but am having some problems. I have the outlines of the countries which I want engraved but to cut the outline of the continent. I am having problems doing...
Results 1 to 13 of 13