Search:

Type: Posts; User: Russ D Wood; Keyword(s):

Page 1 of 3 1 2 3

Search: Search took 0.01 seconds.

  1. Replies
    18
    Views
    11,477

    My piping is all 4 inch but I think the main...

    My piping is all 4 inch but I think the main issue with DC is the total CFM of the DC. I know that others talk about leaks and good blast gates, but I have a pretty good system that even keeps up...
  2. Thread: 3d masks

    by Russ D Wood
    Replies
    5
    Views
    2,521

    Stan, whose long endmills did you use? Russ

    Stan, whose long endmills did you use? Russ
  3. Replies
    11
    Views
    3,144

    My local 'sink' shops used to give me their...

    My local 'sink' shops used to give me their 'scrap' but lately they have been ordering their counters precut! Shucks! Russ
  4. Replies
    25
    Views
    7,821

    I've got a cheapo laser and when my machine does...

    I've got a cheapo laser and when my machine does that it is usually out of focus. It doesn't take much. It also shows up if the material is the least bit reflective as the laser light seems to want...
  5. Replies
    0
    Views
    752

    Cool woodworking project for a school

    How's this for a cool woodworking project for a school! Russ

    http://www.coloradonewmexicosteamtrain.org/FriendsForum/viewtopic.php?f=64&t=1330
  6. Replies
    16
    Views
    2,408

    Well so far I have been through all of the focus,...

    Well so far I have been through all of the focus, leveling, distance, clean up steps as listed in my manual. I can cut everthing BUT ply so it is still my assumption that it is my stash of ply...
  7. Replies
    16
    Views
    2,408

    Once again I want to thank all of you that have...

    Once again I want to thank all of you that have replied. I am a model builder and have been putting together for years, both scratch-built and from kits. I love the so called 'laser kits' where...
  8. Replies
    16
    Views
    2,408

    Thanks gang for all of the replies. The problem...

    Thanks gang for all of the replies. The problem was / is defintely on MY end and not the machine. I finally got it to cut some cardstock so I knew it was in fact working, then I tried a bunch of...
  9. Replies
    16
    Views
    2,408

    Hi Glen, I was reluctant to mention the laser or...

    Hi Glen, I was reluctant to mention the laser or their software because I'm sure the problem is on my end not theirs! :D I did finally get a vector to cut but only in some very light cardstock. I...
  10. Replies
    16
    Views
    2,408

    Newbie question

    Just got my laser. I have it working (almost). I can do a really nice raster image but I can't currently do a vector CUT. The machine and software is not the issue I don't believe. I believe the...
  11. Replies
    44
    Views
    25,210

    I use the sanding mops from StockRoom Supply. ...

    I use the sanding mops from StockRoom Supply. They work really well. I use them in a powered hand drill so I can vary the speeds. Russ
    ...
  12. Replies
    2
    Views
    729

    Thank you Martin for the information I appreciate...

    Thank you Martin for the information I appreciate it! Russ
  13. Replies
    2
    Views
    729

    Suppliers Sticky?

    OK silly question, is there a good resource for looking up suppliers of substrates suitable for laser engraving / cutting? Thanks in advance. Russ
  14. Replies
    5
    Views
    2,740

    What did the 'chips' feel like! Were they cool...

    What did the 'chips' feel like! Were they cool or warm, when through cutting was the router bit cool or warm to the touch. Cool bit, warm chips is what you want. You want the heat to follow the...
  15. Replies
    9
    Views
    3,581

    Marty how long did it take you to clean your shop...

    Marty how long did it take you to clean your shop in order to take that great shop pix! [:)] Russ
  16. Thread: US Quarter

    by Russ D Wood
    Replies
    1
    Views
    1,981

    Rockler has one for sale. Russ ...

    Rockler has one for sale. Russ

    http://www.rockler.com/product.cfm?page=6400
  17. Replies
    2
    Views
    1,304

    It all depends on the type of work being done on...

    It all depends on the type of work being done on the bench. I do a lot of little hand work on one of benchs and on that bench I have mounted the light a little lower but seems like I end using a...
  18. Replies
    17
    Views
    34,631

    I bought one of these kits a while ago and just...

    I bought one of these kits a while ago and just love the results. Russ

    http://www.stockroomsupply.ca/shop/drum-sanders/30-x-4-v-drum-the-works-kit.html
  19. Replies
    24
    Views
    6,219

    I have a computer next to my cnc machine and use...

    I have a computer next to my cnc machine and use these guys 'bags' to cover it with no problems. You might want to see if they have something that is close to the size you want. Russ
    ...
  20. Replies
    39
    Views
    8,611

    I don't have any issues about DC. It even keeps...

    I don't have any issues about DC. It even keeps up with my 24 inch planner but the planner does require frequent bag dumps! :D Russ

    http://www.woodmastertools.com/NS/accessdetail.cfm?PID=88
  21. Thread: Oak Score!

    by Russ D Wood
    Replies
    19
    Views
    3,539

    Well ya see real dried lumber is not near as...

    Well ya see real dried lumber is not near as heavy as the box stores dried lumber! :) Russ
  22. Replies
    11
    Views
    2,448

    What does the U S Buildings technical support...

    What does the U S Buildings technical support people say? Russ
  23. "have to learn a new language first" LOL - yep,...

    "have to learn a new language first" LOL - yep, when i got my ShopBot I already had computer and cad skills but . . . . All of the cnc router STUFF was written assuming that I had woodworking...
  24. Replies
    12
    Views
    2,670

    "The vinyl tiles can become very slippery when...

    "The vinyl tiles can become very slippery when covered with a thin layer of sawdust..."

    YEP! Had tile in my basement shop and it was great right up to the point you started up the ts or the bs...
  25. One question and one response, first the...

    One question and one response, first the question, can you download the control software for your Camaster? Response, by all means get the Aspire it is head and sholders above vCarve and vCarve is...
Results 1 to 25 of 64
Page 1 of 3 1 2 3