I have a Fuji Semi-Pro 2 gravity. Yea, I might be able to get the backs off.
Type: Posts; User: Matthew Sherman; Keyword(s):
I have a Fuji Semi-Pro 2 gravity. Yea, I might be able to get the backs off.
We moved earlier this year and with with my tools not set back up yet I ordered some unfinished cabinets to put in my office. I wished these came with prefinished interior plywood, but they did not...
Sounds like it is good idea to wait for now. I am in Ohio and house is around 20 years old. I do have a little water intrusion is one little spot where there is a small crack near one of the tie...
I moved earlier this year and went from a garage shop to a basement shop. Granted it is a slightly larger area about 21x40 and has double doors with a ramp so moving equipment in was not an issue....
I would consult an engineer first to check the limit on what you can hang from the beams. Any failure in those two beams would be catastrophic for the structure. It might be OK for it to support 400...
Working on a project today I found I needed a pattern bit. It is between the two bits below. 3/4" diameter by 1-1/4" length and 1/2" shank I was leaning towards the Amana because it has the shear...
I have a nice Purdy brush I use for Shellac. So far I have only used clear Shellac with it and I usually just let it dry without cleaning it. Then put it in alcohol before using it again. Yesterday I...
Check out the http://www.forestryforum.com/ ... you can probably find someone near you.
I have built and already completed a changing table for our baby room. For the finish on this I used an oil based varnish. It worked well. I just completed the crib and I am ready to put the finish...
Update... After sanding with 80 grit and getting the little stain seeping through I did start bleaching like Bob said. I didn't get any really strong stuff. I did 2 coats of Clorox then neutralized...
I didn't really get that technical when designing mine. I just laid out the lines using the places they could potentially go and then trying to make the shortest runs. I attached some pictures.
...
I have mine running through 4" pipe with a Thien separator. My maximum lengths are probably 25-30'. I probably could use more CFM, but it is what I went with because I have a small area in my garage....
I agree... same unit I have and I also have a dedicated 20amp circuit. Never had it pop the breaker. I did have my kill-a-watt unit hooked up to measure kwh and it is rated for 15 amps. That will...
Yes, that is correct. The amperage is the more important number concerning proper sizing of the outlet and wire. However if you measure your house voltage it should be right around 120v now days....
I ordered a couple quarts of the Charles Neil's stuff. I sanded with 80 grit tonight. This seemed to remove most of the stain, but there are still some areas that the stain comes back through. Do I...
Check out Marc's episode on jointer setup. http://thewoodwhisperer.com/jointer-setup/
Ok, thanks. I found that Charles Neil's stuff. I wish I would have found that before staining.:p I ordered some and stripped it tonight. The stripper didn't remove all the stain, but lightened it. I...
I did some reading before starting to finish the cherry coffee table I built. I used the Varathane wood conditioner and followed the instructions. I then put a red chestnut stain on top. Even with...
Thanks for linking that place. I was browsing their prices and they are very reasonable. When I need mine sharpened I am trying them out.
I just put in an order at Amazon last night for the Milwaukee one. It is down to $60 with free shipping. It was given the 2nd place in the Fine Woodworking article and had A marks for the most part...
+1 for Freud Diablo. I have the 50 tooth combo blade and it makes very smooth cuts. Very little tear-out when crosscutting plywood as well.
The Wood Whisperer has the method he uses in the FAQ.
http://thewoodwhisperer.com/faq/
I picked up the Triton 3-1/4 from Woodcraft and it arrived yesterday. I had to pick up longer machines screws to mount it in the table and redrill the lift handle hole because the two models have...
I only ran the router to create a quick video. I didn't have the spring removed, but it didn't seem to make much of a difference. One take in the video I didn't have it locked down and that was...
What is kinda of funny is I wasn't locking the plunge down to start. When I down lock it down it vibrates more. It actually has less vibration when it is not locked down.