Search:

Type: Posts; User: Mike Mackenzie; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.04 seconds; generated 32 minute(s) ago.

  1. Replies
    3
    Views
    1,160

    Paul, Lesson learned however I do not...

    Paul,

    Lesson learned however I do not understand why you are doing it this way. If you are spending $237.00 + glue + shipping + labor to glue your own optic into your bracket instead of just...
  2. Replies
    39
    Views
    7,307

    I agree with you rich, If you have a vacuum your...

    I agree with you rich, If you have a vacuum your top door lids would break and you would not be able to open the top door. The systems are made with fresh air intakes to allow for the proper air flow...
  3. Replies
    14
    Views
    1,873

    Scott, This is not the same driver as you use...

    Scott,

    This is not the same driver as you use on your system on these systems they have been using the same driver for years and they are very stable.

    Shannon,

    If you want to see if the...
  4. Replies
    39
    Views
    7,307

    Joe, What system was it? I would say if it...

    Joe,

    What system was it?

    I would say if it was me I would use water or smother it or the new halon extinguishers. I have rebuilt several fire victims and the worst thing is cleaning out all of...
  5. Replies
    14
    Views
    1,873

    Scott, These fonts he questioned about are the...

    Scott, These fonts he questioned about are the most noticeable when it comes to double image.

    Shannon,

    What you should do is tune the system draw a rectangle .5 x 2 fill it and remove any...
  6. Replies
    14
    Views
    1,873

    Shannon, This sounds like you have a worn X...

    Shannon,

    This sounds like you have a worn X axis belt. Try moving the plate over in the X direction line it up at the 6" or 8" on the ruler and test the engraving again. If it gets better then you...
  7. Replies
    6
    Views
    1,671

    Jacob, Check what version of firmware is on...

    Jacob,

    Check what version of firmware is on the system.

    Turn system on once ready press escape
    move down to preferences press select
    move down to about and press select
    what is this number?
  8. Replies
    4
    Views
    4,507

    Jeff, First thing is to start fresh, Get rid...

    Jeff,

    First thing is to start fresh, Get rid of any and all drivers you have loaded for the laser. You must go into the server properties and delete the system from this location as well.
    Then...
  9. Mike, The important thing to keep in mind here...

    Mike,

    The important thing to keep in mind here is your machine, These ideas are all great however your system will have a difficult time working with these materials.

    Your system is pushing 20...
  10. Replies
    7
    Views
    1,220

    Joseph, You can simply jumper across two pins...

    Joseph,

    You can simply jumper across two pins to make it look like the table is in there without taking the connector on and off just use a paper clip. Look at the mating connector and jumper...
  11. This probably has a lot to do with there cutting...

    This probably has a lot to do with there cutting capabilities.

    Laser Equipment Specifications & CapabilitiesHoused in a 4,800 square foot facility, Boston Lasers invests in equipment and...
  12. James, Download this driver it will work with...

    James,

    Download this driver it will work with both 32 and 64 bit

    http://www.ulsinc.com/downloads/#

    Note this is for the VLS 2.30 & 3.50 if you have the VL 200 / VL300 you need this driver
    ...
  13. Replies
    5
    Views
    1,307

    Pete, On your PS model it will be controlled...

    Pete,

    On your PS model it will be controlled by the way it is drawn.
  14. I could not get the attachment to the above post...

    I could not get the attachment to the above post so lets try this one.

    OK the file is to big PM me your e-mail address and I will send it to you.
  15. ULS 25PS instructions

    Gabe,

    I hate to be the bearer of bad news BUT this sounds like the laser tube has or is going out. clean the cooling fins on the tube and make sure that the cooling fans are working top and bottom...
  16. Replies
    11
    Views
    1,982

    Bob, Remove the cone and run the air see if...

    Bob,

    Remove the cone and run the air see if you get the same mark. You may have a leak in the air line somewhere that causes the cone to pull in the air instead of blowing it through the cone.
    ...
  17. Replies
    19
    Views
    3,050

    Kevin there are open paths in the vector lines...

    Kevin there are open paths in the vector lines also you may have to make the Oval in the center two separate pcs top section and bottom section. You need to work with closed vector paths. I believe...
  18. Replies
    6
    Views
    1,384

    you mean like this,

    you mean like this,
  19. Matt, Take the 9 Volt battery out.

    Matt,

    Take the 9 Volt battery out.
  20. Replies
    12
    Views
    5,789

    Check the voltage of the power supplies they...

    Check the voltage of the power supplies they should be a solid +48V. You may have a power supply issue instead of the tube.
  21. The reason the Z motors have to be changed is due...

    The reason the Z motors have to be changed is due to a higher torque Z Motor that they use now so the CPU and Z motor are matched. This would only need to be done if you have to replace the CPU on an...
  22. Replies
    2
    Views
    1,519

    Check with Photovac lasers in Ohio

    Check with Photovac lasers in Ohio
  23. Replies
    9
    Views
    1,701

    Aleta, What we do to adjust our rulers is use...

    Aleta,

    What we do to adjust our rulers is use CorelDraw set the page size to your engraving field size then add the page frame, set it to vector and then print it to the system. Place some masking...
  24. Replies
    4
    Views
    2,963

    Todd, These are symptoms of the tube, Try...

    Todd,

    These are symptoms of the tube, Try removing the back cover and make sure it is just not overheating. This will also expose the serial # and date You will need this to get one on order.
    ...
  25. Donnie, Do you notice this just with the HPDFO...

    Donnie,

    Do you notice this just with the HPDFO optic? This sounds like an alignment problem but it could be the HPDFO optics as well. Also make sure that the laser tube is correctly mounted and...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4