Search:

Type: Posts; User: Dan Hammerstron; Keyword(s):

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. I have imported 2 Chinese machines, the first was...

    I have imported 2 Chinese machines, the first was a 6090 and then a full sized 1325 300mm gantry heigth with 6hp. spindle and vacuum table and vacuum system, its running on mach3 it has Yako drives...
  2. Replies
    13
    Views
    3,354

    Had to make 100 wooden pucks for coy cup...

    Had to make 100 wooden pucks for coy cup playoffs, they wanted a diamond pattern on the edge, so I used the rotary from the cnc which has a 100mm chuck, I had to change the setting on the driver, it...
  3. Yes it does, up to ver.4 but its just as fast to...

    Yes it does, up to ver.4 but its just as fast to use a swap file and the RDcam software.
  4. I apologize then Dan, "soul crushing" hmmm, I am...

    I apologize then Dan, "soul crushing" hmmm, I am Kinda familiar with Cnc equipment and rampings and step motors and servo's I have built a few cnc's. I have trashed gears and racks testing motors and...
  5. Wow, what constructive intelligent posts...gotta...

    Wow, what constructive intelligent posts...gotta be proud.
  6. 273477This Co. made the controllers for ULS up...

    273477This Co. made the controllers for ULS up till quite recently according to Thomas Hart the CEO. of Testra, He has offered to let me try this out on my 1390 Keyland laser and I am going to take...
  7. 273473I just talked to Tom Hart, he is the...

    273473I just talked to Tom Hart, he is the President of the Co. It is a WYCIWYG and works the same as the universal driver from CorelDraw, I have a universal and love it. The 256 greyscale is for 3d...
  8. Kay, the software you use is CorelDraw and you...

    Kay, the software you use is CorelDraw and you send to the laser the same as you used to? also the speed is doubled from 50in. per to 100 in. per. according to there manual they sent, it says its...
  9. This company is using Testra laser system....

    This company is using Testra laser system. http://emissiontechnologies.com/
  10. I found some more info on the Testra system....

    I found some more info on the Testra system. http://www.powerpr.com/articles/articles.asp?include=134736
  11. I am pretty sure this" ...

    I am pretty sure this" http://2laser.com/upgrades_parts_consumables " company is using the Testra laser system on there high end machines, I have had many emails swapped with a person at this...
  12. Widows print driver & control system for chinese machines.

    Hi, are there any Machines out there that have converted to the Testra system.? This is the email I received from them. Our controls...
  13. Replies
    9
    Views
    1,503

    I modified a Chinese to fit on there and it...

    I modified a Chinese to fit on there and it created other problems so went back to the home made one. The problem was it makes the snout to long and the direct air when lasering lamacoids isn't as...
  14. Replies
    12
    Views
    25,834

    Yes, I started with a 2hp grizz dust collector,...

    Yes, I started with a 2hp grizz dust collector, 6in. tubing. but "the noise". now have these two.266683They work very well hooked up to 1390 and uls. laser
  15. Replies
    9
    Views
    1,503

    266682homemade air assist . uls50e

    266682homemade air assist . uls50e
  16. You are correct, and I didn't mean to...

    You are correct, and I didn't mean to "generalize" but in all my pre-buy looking I never come across any info or comments about the cost of returning tubes or that "some" companies that assemble...
  17. Again, I will say..if the tube in your machine...

    Again, I will say..if the tube in your machine goes in the time limits of thier stated warranty and if they require you to send the tube back to get the warranty..(then the warranty is useless)...
  18. Yes Rodney, I have started with the company that...

    Yes Rodney, I have started with the company that assembled the laser and progressed to EFR direct and they will honour the warranty..no problem... but they want the whole undamaged tube returned to...
  19. First off, i'm not new to lasers..have had one...

    First off, i'm not new to lasers..have had one and sometimes two since 1998. I also have cnc's and other machinery.
    and in my post up above you will read that I begged them to reduce thier terms on...
  20. I think there should be a great big " stickey" on all main laser forum pages.

    chinese machinery have "NO WARRANTY" there "guarantee" is useless (they require proof that parts are defective and ask for its return) by doing this the cost of return "shipping back" cost more than...
  21. Replies
    8
    Views
    4,066

    Mike, what machine do you have with a 280 watt...

    Mike, what machine do you have with a 280 watt tube? Thats the kind of tube I want..we do furniture and a clean cut of 18mm would be nice.
  22. Replies
    8
    Views
    1,806

    C:\Program Files\Corel\CorelDRAW Graphics Suite...

    C:\Program Files\Corel\CorelDRAW Graphics Suite X3\Programs....corelpp will be in there..
  23. its fixed..wiring connection...

    its fixed..wiring connection...
  24. Yes, both the dsp and computer commands, the...

    Yes, both the dsp and computer commands, the laser power settings only work from 8% laser power its starts and rapidly rises to max power at 20% after that it just stays on max power..
    Its a keyland...
  25. I guess I had better explain a little clearer.....

    I guess I had better explain a little clearer.. What the laser dsp controller and the computer do is the laser starts firing at 8% power level and by 20% its at full power, how I checked it (so many...
Results 1 to 25 of 28
Page 1 of 2 1 2