Search:

Type: Posts; User: david blakelock; Keyword(s):

Page 1 of 4 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    45
    Views
    7,182

    Not to get this topic way off subject, but the...

    Not to get this topic way off subject, but the statement about software cost going through the roof based on subscription pricing is simply not true. If anything the pricing has gone down if you look...
  2. Replies
    45
    Views
    7,182

    Just a note on subscription vs perpetual license....

    Just a note on subscription vs perpetual license. Most software companies are moving to a subscription model. For a number of reasons, the main one is that it is easier to get started as the up front...
  3. Replies
    8
    Views
    2,363

    Check out www.blackforestwood.com...

    Check out www.blackforestwood.com. I follow them on Instagram. They do amazing epoxy tops and I believe they sell the epoxy. They have many videos on Instagram which are probably accessible on the...
  4. Here is the link to the part...

    Here is the link to the part https://www.oneida-air.com/inventoryd.asp?item_no=GCOLLECT13. I agree that the inlet is too small and most likely a manufacturing error. Which if that is the case totally...
  5. Something doesn't make sense. I just installed my...

    Something doesn't make sense. I just installed my system and had no issues. The part that I used was an 8" machine adapter. Part number GAM0800000. It just slid right in, although it was a tight fit,...
  6. So far I have not done either. I might run a bead...

    So far I have not done either. I might run a bead of silicone around it, but doesn't seem to really need it.

    Good luck with the rest of the installation
  7. I used the standard one that they shipped. I have...

    I used the standard one that they shipped. I have to say that I was very pleased with Oneida. The design was well laid out and all the parts fit great. Really had no issues. The only thing...
  8. I just installed my system. The sleeve fits...

    I just installed my system. The sleeve fits inside and then the quick connect straight pipe attaches to that sleeve. It was simple. It sounds like you have the wrong part. I had them do the design...
  9. Replies
    19
    Views
    12,966

    Not to divert this thread, but I just installed...

    Not to divert this thread, but I just installed this vise as well. As has been pointed out, it is critical to follow the instructions. It is not that difficult if you take the time and make sure...
  10. Replies
    7
    Views
    1,719

    Probably not quite the stlye you are looking for,...

    Probably not quite the stlye you are looking for, but you might check out:

    http://www.hairpinlegs.com/

    David
  11. Replies
    7
    Views
    1,719

    Prashun, when you say vintage what era/style are...

    Prashun, when you say vintage what era/style are you looking for? You might pick up a copy of a magazine called Atomic Ranch. They have adds for companies that supply vintage steel legs. Not sure if...
  12. Replies
    18
    Views
    12,974

    Aaron, you are just around the corner from us. We...

    Aaron, you are just around the corner from us. We live at Walnut Hill between Midway and Inwood. Welcome to the hood. If you need any suggestions for places to go in the area just let me know.
    ...
  13. Replies
    18
    Views
    12,974

    Welcome to Dallas Aaron. Glad you survived the...

    Welcome to Dallas Aaron. Glad you survived the hottest summer we have ever had. It was to hot to do much of anything this summer. I don't know of any hardwood dealers other than Wood World. There...
  14. Replies
    6
    Views
    1,152

    Check out this months issue of Woodsmith. I...

    Check out this months issue of Woodsmith. I believe it has just what you are looking for.
  15. Ryan, no worries at all. If you have a sketch and...

    Ryan, no worries at all. If you have a sketch and don't mind scanning it I would greatly appreciate it. But please don't go thru any troubles to do it. You can send me a PM with the sketch. It looks...
  16. Ryan, great job on the chair. Did you have a plan...

    Ryan, great job on the chair. Did you have a plan that you worked from? I love the Danish modern look as well as am always on the look out for plans and ideas.

    Thanks,

    David
  17. Replies
    34
    Views
    8,269

    Tom, I will bite as well as I had many of the...

    Tom, I will bite as well as I had many of the same questions when I was planning my shop. Obviously there are a lot of variables in building a shop, but here is what I did. I built a 1000 sg. ft...
  18. Replies
    57
    Views
    17,043

    Joe, you are right that the whole subject of...

    Joe, you are right that the whole subject of cyclones can give you tired head. I have started at least one thread on this subject and have read just about every thread related to dust collection....
  19. Replies
    33
    Views
    13,131

    When I visited the ClearVue factory in Seattle a...

    When I visited the ClearVue factory in Seattle a couple of weeks ago, I asked them about this. They pretty much chuckled and said don't worry. They run all PVC pipe to their machines and have no...
  20. Replies
    12
    Views
    2,631

    David, that is strange. The site is working so...

    David, that is strange. The site is working so that is not the problem. I access it through IE, not sure what browser you are using, but that might be a problem alhough highly doubtful. I tend to...
  21. Replies
    12
    Views
    2,631

    Jim, thanks for the feedback. David, here is...

    Jim, thanks for the feedback.

    David, here is the contact information you requested:

    Email:Sales@clearvuecyclones.com
    After Sales Support (Please use this e-mail for all after-sales support...
  22. Replies
    12
    Views
    2,631

    Neil, I agree with you that it is not the best,...

    Neil, I agree with you that it is not the best, but it has a lot of good information. Since I have to a trip report when ever I visit a customer/prospect for my boss, I thought I would do a trip...
  23. Replies
    12
    Views
    2,631

    Yea, they did not appear to be the most computer...

    Yea, they did not appear to be the most computer savy folks. You can tell by their website, not one of the best. But great guys to do business with and they have what I think is a great product. The...
  24. Replies
    12
    Views
    2,631

    Clearvue Factory Visit

    I was in Seattle yesterday on business and found myself with some time to kill before my flight, so I rang up the folks at Clearvue and asked if I could stop by. Of course they said yes, just come on...
  25. Replies
    18
    Views
    12,128

    Mark, I had the large and upgraded to the XL. It...

    Mark, I had the large and upgraded to the XL. It is harder to control the temperature with an XL for a low slow burn. I solved the problem by buying a real pit smoker made by a place in Houston for...
Results 1 to 25 of 90
Page 1 of 4 1 2 3 4