Search:

Type: Posts; User: michael osadchuk; Keyword(s):

Page 1 of 11 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    17
    Views
    2,887

    If the cracks are hairline/tight, do you mean no...

    If the cracks are hairline/tight, do you mean no opening.... if so, how would any glue or filler penetrate below the surface and, if not, do any good?

    If there is a crack=opening, I would use slow...
  2. Replies
    9
    Views
    10,737

    Bernie LeBlanc from NH posted pictures of his...

    Bernie LeBlanc from NH posted pictures of his workbench build around embedded T-tracks and posted pictures on the Canadian Woodworking website....look in the general 'woodworking' pages around...
  3. Replies
    23
    Views
    8,423

    Rick, The splitter/support column for the...

    Rick,

    The splitter/support column for the shroud is anchored by a racheting handle like this:

    http://www.busybeetools.com/products/KNOB-HANDLE-ADJUSTABLE-2IN.-X-5%7B47%7D16IN.-X18-TPI.html
    ...
  4. Peter Thanks for posting your air cleaner(s)...

    Peter

    Thanks for posting your air cleaner(s) solution; it's quite interesting and, given the Dylos particle readings, pretty effective.

    It's interesting to underline that maintain some kind of...
  5. Replies
    9
    Views
    4,937

    The material safety data sheet on De-Gluegoo...

    The material safety data sheet on De-Gluegoo (available on its website as a link under the heading 'composition') states that the active chemical ingredient is "methyl cellulose acetic acid diluted...
  6. Replies
    6
    Views
    3,441

    I recycled a 4 foot garden bench with iron ends...

    I recycled a 4 foot garden bench with iron ends my adult inherited with the purchase of century house and it was fairly simple, nice project.....
    ..... teak is the wood for outdoor use though very...
  7. Peter, I'm not a doctor..... but it sounds...

    Peter,

    I'm not a doctor..... but it sounds from the above that your immune system has been comprised.....

    the bad news is, of course, if this is the case, that it could get worse if you don't...
  8. Consider getting a Dylos .5/2.5 micron calibrated...

    Consider getting a Dylos .5/2.5 micron calibrated particle counter to get some empirically based information on what is working and what isn't .... perhaps have it in place after you do the...
  9. I agree with Bob and others that MEC is the key...

    I agree with Bob and others that MEC is the key factor to pay attention to in knowing when to use wood, whether kiln or air dried.

    Letting new bought kiln or air dried timber 'acclimatize' to the...
  10. Replies
    26
    Views
    3,328

    Ditto the Sharkguard for overhead dust...

    Ditto the Sharkguard for overhead dust collection... I have the 4" mega mouth option connected to a 2hp dc but I don't doubt that shop vac sized mouth would also work well.......

    good luck
    ...
  11. I didn't hear anything in the demo video about...

    I didn't hear anything in the demo video about how to register to the blade/chisel,etc. to specific bevel angles so I assume no angle registration feature is built into a jig with an intro price of...
  12. Replies
    19
    Views
    6,496

    I agree with John Sandford, Scott and others on...

    I agree with John Sandford, Scott and others on going the used tablesaw route....... but it takes some research, patience and decisiveness...

    research by going thru some woodworking forums on what...
  13. Ian hmmm.... mounting a Veritas twin screw...

    Ian

    hmmm.... mounting a Veritas twin screw vise VERTICALLY... that is quite a tangent and I think deserves its own thread and would, without doubt, attract lots of advice and comment....

    my two...
  14. Bill I've countersunk the nuts without an...

    Bill

    I've countersunk the nuts without an adverse consequence in the dozen or so years after the installation of the vise..... my benchtop rests on several 4.5" wide wood pillars that run the...
  15. Replies
    7
    Views
    3,061

    Decide on the vices you want before you finalize...

    Decide on the vices you want before you finalize the design of bench.
    (I have a long bench: I put two of the smallest Record quick release metal vises on the front and LV twin screw on one end)
    ...
  16. Replies
    31
    Views
    5,853

    Yup, the new hybrid species are called eastern...

    Yup, the new hybrid species are called eastern coyotes or coywolf........ here is link to an interesting 45 minute documentary on this hybrid that is showing up in Eastern North America, including...
  17. Replies
    76
    Views
    11,343

    Hi All Thanks for all the personal stories of...

    Hi All

    Thanks for all the personal stories of hearing loss/tinnitus...... I still have pretty much all my hearing and your stories are a good kick in the pants to remind me to use hearing...
  18. Replies
    78
    Views
    11,769

    A couple of comments...... The sales of the...

    A couple of comments......

    The sales of the venerable domestic General cabinet saw model 350/650 (I have one) in recent years declined from thousands to hundreds per year and was, among other...
  19. Replies
    15
    Views
    2,917

    Dave, A couple/three suggestions and what I've...

    Dave,

    A couple/three suggestions and what I've done.....

    Make yourself a hole location template out of hardboard/thin plywood...... so that you won't have to buy planing stops with moveable...
  20. Replies
    352
    Views
    51,300

    Please count me in. michael

    Please count me in.

    michael
  21. Replies
    45
    Views
    6,050

    Paul, I'm in Canada but have read user...

    Paul,

    I'm in Canada but have read user accounts of the nominal 2 horsepower HF single stage dust collector on the U.S. woodworking forums, including Phil Thien's 'baffle separator' discussion...
  22. Bill, Just to cherry pick on questions 3 and 4...

    Bill,

    Just to cherry pick on questions 3 and 4 on the Dylos.... I've had the 1/5 micron Dylos particle counter for five years now and make the same assumption you speculate in question 4 - that...
  23. Augusto, I think that after you rip each 2 x...

    Augusto,

    I think that after you rip each 2 x 12 board into 4 pieces, you are good to glue the faces of each of these pieces together .... the faces of milled 2 by stock from the lumberyards should...
  24. Augusto, Can you clarify the width and...

    Augusto,

    Can you clarify the width and thickness dimension 12 x 16 (kiln?)dry douglas fir that you still have to rip with a circular saw before you can handplane a face and edge before running...
  25. Ditto Thomas's comment. michael

    Ditto Thomas's comment.

    michael
Results 1 to 25 of 274
Page 1 of 11 1 2 3 4