Search:

Thanks Dick Brown and Bruce Wrenn for the great tip!

planing would be an option, but I dint have one. Nor a drum sander. I’ve used drum sanders in the past and they do a good job at leaning up old boards that just might have a surprise to Knick a...

I just replaced a deck and saved all the 20foot clear redwood deck boards . Since they are mostly in salvageable shape I’d like to resurface them with a drum sander. I found a used jet 10 20 , and am...

Interesting thread. I like the airbag concept behind the reaxx technology. Just replace a gas cartridge, It doesn’t ruin a blade or brake cartridge and I’m sure it would be a contender in a cabinet...

This is the first I’ve heard of the Max, which was built in San Jose CA, being associated with State. However it does sound like we are talking about the same machine. Outs has a threaded end on the...

I haven’t given up on the Max yet. Problem is it is near impossible to replace the sandpaper on the rubber drums. Most sleeves available are too small, only some barely fit. Last time I had to...

I work in a school shop at a community college. We are looking to replace our Max spindle sander with a Grizzly 1071, or a Laguna SS/24T .

While the Grizzly costs less, it seems to have problems...

Ive been using it . I am looking for what can go wrong in our environment of many users. I like the fact the the splitter tilts with the blade. The splitter is easy to remove and replace. When using...

i
rankie and JimInstalled it yesterday. Total time 3 hours, two people. After careful measurement We determined that removal of the angle iron that came with the biesemeyer fence set up was not...

Really good suggestions, especially the addition on the door. Thanks again Frankie. I'll let you know how it went.

Thanks for that photo, we have a right tilt unisaw with the metal cover. It's in a school shop at a community college trade school and because so many people need the saw all the time, I really have...

Do you have any problems with the tubing interfering with the cabinet door? We need access to receive pressure washers, etc as they are dropped down. (We are a trade school). We want the door on and...

Thanks Frankie,
I just got off the line with Steve at Delta and he advised removing and replacing the angle with a strap. Which is what we already knew. I considered doing what you did , but when...

No, the angle interferes with the tubing of the guard. Thanks for the suggestion though.

I am about to install the Delta Uniguard 34-976 on out Delta Unisaw that has a Biesemeyer fence and a 52 inch extension table. The Biesemeyer fence system has a sturdy angle iron on the outfeed side...

So far so good, no more humming after all connections tightened and lots of use. Thanks for all the help.

I had an electrician check that all connections are tight and measure line voltages on all three legs. One leg had a very slight voltage reading. He found a couple of places that needed tightening ,...

I had an electrician check tha all connections are tight and measure line voltages on all three legs. One leg had a very slight voltage reading. He found a couple of places that needed tightening ,...

it's the original 3 phase motor that came new with the saw hooked to 3 phase power. All connections from switch to starter are tight. Intermittent problem, and can not figure out why manually...

Yeah, I know, I tried it.

Our 3 phase unisaw intermittently hums and will only start if the blade is turned by hand a bit (saw unplugged) and switch activated a second time . All the wire connections have been checked and...

I have been trying to get a Delta 31-255x 18x36 drum sander working again. It is a machine at our community college where I volunteer. One of the students destroyed the nylon gears which I removed...

The part is not available anywhere now. We need it for our community college wood shop. Has anyone had any success with the Grizzly part? If you have the drawings Jim that might help us.

Thank...

Yes Todd I edited my original post with it right after I replied but it didn't go through apparently. Like you I went nuts trying to find a key. I also called cushman and let them know.

What is...

I just found a Milwaukee that works on my cushman jt33 13L japan chuck which came on my Rockwell 15-069 dp.