Search:

Type: Posts; User: Jim Ritter; Keyword(s):

Page 1 of 10 1 2 3 4

Search: Search took 0.09 seconds.

  1. Thread: Bench Apron

    by Jim Ritter
    Replies
    39
    Views
    1,878

    An apron would not work for me. I clamp down on...

    An apron would not work for me. I clamp down on the front of the bench way too often not to have that convenient edge.
    jim
  2. Thread: It Spins!

    by Jim Ritter
    Replies
    20
    Views
    2,075

    Winton the chain is easily adjusted to have the...

    Winton the chain is easily adjusted to have the jaw parallel at full clamping tension. Once set there is little need to adjust unless you want to clamp something that is out of parallel to begin...
  3. Replies
    20
    Views
    1,035

    I'm pretty sure it was for a screw type holdfast...

    I'm pretty sure it was for a screw type holdfast with a flat bar. The bar kept the screw upright. I've got some old catalogs, I'll take a look when I get to the shop.
    jim
  4. Replies
    13
    Views
    1,497

    Definitely a replacement handle, I have a bunch...

    Definitely a replacement handle, I have a bunch of those handles around the shop. Just got a Bell System axe this summer. Also have a couple braces, a screwdriver and wire cutters. Good tools.
    jim
  5. Replies
    8
    Views
    739

    Any chance you can post a photo of the screw at...

    Any chance you can post a photo of the screw at the handle end? We might have some other ideas if we can see what you are working with. You got good advise so far, but there might be others.
    jim
  6. I think Shop Notes did an article about one. I'll...

    I think Shop Notes did an article about one. I'll have to look and see if I can find it.
    Jim

    OK, found it, it is in ShopNotes number 115 page 36. It's well thought out, I wanted to build one when...
  7. Replies
    181
    Views
    31,543

    Very nice Ralph. Was the body cast or made up...

    Very nice Ralph. Was the body cast or made up from plate? Glad to see you are still at it.
    Jim
  8. Replies
    17
    Views
    1,643

    John here are a couple of pics of my real life...

    John here are a couple of pics of my real life tests. Somewhat subjetiive because I didn't have a scale on the handle but these are as I would use the vise. When I read as above where some want the...
  9. Replies
    17
    Views
    1,643

    Please don't use bicycle chain. It is not strong...

    Please don't use bicycle chain. It is not strong enough. If you are making your own use #35 roller chain. I measured upwards of 600 pounds tension depending on the distance from the screw. I've got...
  10. Thread: It Spins!

    by Jim Ritter
    Replies
    20
    Views
    2,075

    Sweet installation Marco, well done. Enjoy it....

    Sweet installation Marco, well done. Enjoy it.
    Jim
  11. Metal Lathes Can't help with info, but it looks like a nice...

    Can't help with info, but it looks like a nice little lathe.
    Jim
  12. I'm guessing you are not married? Jim

    I'm guessing you are not married?
    Jim
  13. Hi Richard of course right after I send you some...

    Hi Richard of course right after I send you some money you ask if I am selling them. No, I'm not selling them. They were the first things I made on my Benchmaster milling machine. I made parts enough...
  14. I made this one one for a swap and couldn't...

    I made this one one for a swap and couldn't decide on the cutter shape so I made a bunch of different ones.
    ...
  15. Replies
    7
    Views
    1,872

    Metal Lathes Any suggestions on disassembling the lathe for...

    Any suggestions on disassembling the lathe for transport? Do I have to cut the flat belt to remove the jack shaft and motor? I'm not sure where to start. The shaper is not following me home. It's...
  16. Replies
    6
    Views
    871

    I have more than a couple #3's and they are all...

    I have more than a couple #3's and they are all Stanley's and I did notice a couple months ago when I hung them up that some are different lengths. Not sure how much time I'll have to measure them...
  17. Replies
    17
    Views
    1,682

    That's a sweet sharpener Pete. I too am a...

    That's a sweet sharpener Pete. I too am a draftsman mostly in my former career, but still have my board set up and draw by hand. I would have bought that sharpener over a new one too.
    Jim
  18. Replies
    5
    Views
    575

    Yes Jim the inside edge of the radius is/was...

    Yes Jim the inside edge of the radius is/was sharpened. I'll try and take a better photo this evening.
    Jim
  19. Replies
    5
    Views
    575

    Yes it is like a scorp, cutting and hollowing on...

    Yes it is like a scorp, cutting and hollowing on the pull stroke. The handle is pinned on so it doesn't pull off. That is interesting about the prosthetics but this is much longer than would be...
  20. Replies
    5
    Views
    575

    Tool ID help needed

    I'm doing a basement clean out to help a neighbor dispose of her fathers tools and this was hanging on the wall. Curiosity has gotten the better of me on this one. I can find no makers marks. Here...
  21. Replies
    33
    Views
    3,778

    Here is a screen shot of Popular Mechanics Aug...

    Here is a screen shot of Popular Mechanics Aug 1930.

    http://i1135.photobucket.com/albums/m628/boatman53/8127cd144ae3c8785f3769c76f05410b_zpsf8512f60.jpg

    Jim
  22. Replies
    7
    Views
    1,872

    Metal Lathes Lathe and shaper

    I have an opportunity to upgrade my Atlas/Craftsman lathe to this Logan. Assuming everything works as it should would you do it?
    ...
  23. Replies
    5
    Views
    670

    I second Bills advise. Jim Edit: welcome to...

    I second Bills advise.
    Jim

    Edit: welcome to the Creek.
  24. Replies
    13
    Views
    1,498

    Those types of drawer inserts can be made in two...

    Those types of drawer inserts can be made in two pieces. The cutouts made with a fret or scroll saw then the bottom plywood is glued on. I'm working on one but I am using a small router bit for doing...
  25. Replies
    33
    Views
    3,778

    +1 not fond of it. With the knobs radiating like...

    +1 not fond of it. With the knobs radiating like that one is almost forced to put the screw lower than one might want. The last version I almost bought but not this one.
    Jim
Results 1 to 25 of 249
Page 1 of 10 1 2 3 4