I have a subpanel that was installed by a licensed electrician but without a permit. I need to get it permitted. The only circuits in the new subpanel are outlets in the garage/workshop. These...
Type: Posts; User: Bill Miltner; Keyword(s):
I have a subpanel that was installed by a licensed electrician but without a permit. I need to get it permitted. The only circuits in the new subpanel are outlets in the garage/workshop. These...
I'm the OP and it just occurred to me that I have enough hose to do a trial run and see how well it works. Duh! I've thought about this for some time and it just didn't occur to me that I have...
I use a Delta 1HP barrel top dust collector to catch the chips from my 10" Jointer/Planer. I know it does not collect all the dust particles so I always wear a quality dust mask. It does an...
I have to agree with the posters above. To the pool it matters little if it take twice as long to push say, 25,000 gallons, at 1600 rpm versus 3200. But the wattage required to run the pump at 1600...
I could have been this way one: loadcalc.net
I know what PT lumber is but am not familiar with WRC.o
I am located in Phoenix, AZ and need to make some "outdoor" side tables. They will be for a covered porch. They should never be "out in the rain" but will receive some direct mornings sun. They could...
Thanks for the response. I tried something similar and it just doesn't have the shear strenght, it jusr shredded over a ahort time.
I need recomendations for a non-slip material I can glue to the feet of my workbench to help resist movement. The workbench is 2" maple and quite heavy but the garage floor is a rolled vinyl diamond...
It physically died. I Tried several power supplys but nothing.
My router has died so I need to buy a new one. I have no idea what model. My uses are: three tablets frequently connected concurrently, two network printers and one network hard drive. No gaming...
Based on drill speed charts I have the speeed would be set between 250 and 500, hardwoods vs softwoods. I suspect the 1700 speed is way too ugh and causing the bit to overheat badly. JMHO
I'd say that over 50% of my purchases have no invoice includes and I average 4-5 shipments a week.
I am having a 100 amp sub panel installed in the garage of my new house. Is one Mfg. better than another? I assume some, but which mfg. should I have installed? So far the new panel will have...
Maurice, the OP was referring to the Bevel Gauge not the angle reference plate from Woodpeckers.
Because I make pieces with a lot of odd angles I have the Veritas Bevel Setter already, but if I...
I don't think I have my manual anymore, but they are available directly from Keller. Maybe this video will suffice. http://www.youtube.com/watch?v=e2l3zeWLD20
I am going to purchase a joinery float (my first) and need a little help. The primary use will be to trim tenons, and possibly mortise sides. Looking at the models on the LN website they show both...
I have a piece of 1/4" thick 6061 aluminum plate that I want to use as a base plate for my 8" circular saw. Any issues with just plunge cutting the slot for the blade?
Thanks for all the replies.
Has anyone here installed their Quicken data files on a shared drive? If so, were there any particular problems areas that I should be aware of? The systems use Windows 7 Pro.
I want to be able to...
Sorry Ray but they are correct. I previously worked for a company that filled aerosol cans. The tube inside is slightly longer than the can height and curved at the bottom. The red dot indicated...
There is an "ultimate" tool rest in SHOPNOTES issue #76
Can anyone tell what the difference is between the PSI Portable Panel Saw System (PSS-2) $154 and the one on the Penn state website for $99 (plus $17 shipping)?
Since you asked, for a variety of reasons Buyers, myself included, generally like to have the price quoted as shipped and like to use Paypal. For me I will not buy an item if I can't use Paypal, as...
Anyone know a good source for a 3/8" thick brass plate at least 4" square?