Search:

Hello,

I have a Ridgid TS3650 table saw. My Stacked dado blades are Freud SD200 8" blades. My problem is there were no instructions. I have been able to do 3/8" dados but if I try 3/4" dado...

hello,

Does anyone know if anyone makes a router lift that will work with a Craftsman Plunge router model # 17517 ? I have 3 craftsman routers and really don't want another router. Thanks
...

Hello,

Just bought a brand new Dewalt DC608K brad nailer on e-bay for $249. It is nice not to have to drag and air hose around anymore. Does anyone else have one of these beauties? Have a great...

Orlando,

I agree with Jason and Jeremy. I have a TS 3650 and the fence system is easy to use and very very accurate.


Joe
...

James,

I have owned a Woodmaster model 712 for several months. This thing is built like a tank. It does an excellent job as a planer, drum sander, it is molding making animal. I haven't used the...

Dave,

I have both Shop Fox and Grizzly tools. The grizzlys have a better fit and finish, but the shop Fox tools work OK. Both companies are owned by the same person. I lean more toward...

Hello,

I have a rockler router table with a split fence. I was wondering if there is a better way to adjust the fences. Currently, I measure from the front of the table to each half of...

Thanks for all the great answers and help. Watching the woodsmith video cleared up a couple of issues I've been having. I am building a miter sled for my tablesaw. I didn't realize my chop saw would...

Hello,

I have just started getting in to making wooden picture frames. Making the molding to use for frame construction is the easy part. My problem is getting the frame the correct size....

Clay,

I too have a difficult time removing or inserting the accessory shaft. Everything has to be lined up perfectly. Woodmaster must have tight tolerances when building these machine. As James...

Hello,

I was thinking about ordering a clamp like this for picture frames. Is it really "Self Squaring". I have the corner blocks for my bessy clamps, but felt this would be easier to square up...

Joe,

I am by no means a pocket hole expert but have used my Kreg kit multiple time. I have found, if you have the 2 pieces of wood clamped and drill the pocket hole at the angle of the...

Bart,

Now I'm embarrassed, my shop usually looks like that. I have a Woodmaster Planer which is a Great Grandchild of your Belsaw. I'll bet yours is even better made and a lot heavier....

Greetings Everyone,

I had a question regarding professionally kiln dried wood. If I purchase Kiln dried boards and stack then off the floor (in an unheated building) will they pic up a lot of...

Kev,

I tried that with 2HP collector and a 1HP collector with the same idea as you. Unfortunately, they fought each other.


Joe

William,

That planer is a beast. Back then American made equipment was the best you could buy. Now it's hard to find 'American Made" anything.


...

Pat,

I just read a detailed 14" Band saw review at Fine woodworking.com. There was a rave review of the Grizzly G0555X 14" Extreme Series Band saw which was rated the best value of all the 14"...

Thanks for the replies. My shop is in a separate building. I also run a Jet 3-Speed 1000 CFM Air Filtration System. I didn't know the trash can cyclone was such a CFM liability. I will just use the...

Shawn,

I guess I left out a huge piece of the equation sorry. 4 in PVC pipe. Thanks

Joe

I have a 2HP 1600 CFM 2 stage (trash can lid cyclone) dust collector. If I attach it to 15 feet of PVC pipe with 1 45° elbow, will I lose a lot of suction? It will be attached to a planer molder....

Hey gang,

I bought one of the HF 2HP 70Gal DC and have been using it for several months. I live close enough to a HF store, I bought it there. It does a good job for my power tools. I'm sure the...

Peter,

The horizontal table makes routering easier. especially when you are trying to router the edge of a board. To me, it seems a little more tedious changing bits because the router is...

Hello,


I’ve seen other members showing shop pictures here. This link will take you to my shop pictures. The jpegs are too big to upload to this site.

Joe
...

Scott,

Congrats on the tool coup!!

How do I post pics here or add a link to my online photos? Thanks


joe

http://web3.automationdirect.com/adc/Home/Home

I'm not sure about pricing. Hope it helps

Joe