Search:

Type: Posts; User: John M Torrez; Keyword(s):

Search: Search took 0.00 seconds.

  1. We had just run out and pulled them from the...

    We had just run out and pulled them from the site. We have more through QC now so they are back up.

    Sorry for any inconvenience.

    Please let me know if there is anything I can help with.
  2. Replies
    12
    Views
    4,568

    Sorry for the delay getting back to you. Our...

    Sorry for the delay getting back to you.

    Our distributor Jeff Birt at www.soigeneris.com will be carrying these and has no minimum order. I'm not sure when they will be on his site but you can...
  3. Replies
    12
    Views
    4,568

    In general I would agree. However, the bearings...

    In general I would agree. However, the bearings are actually quite good in most of these routers. As such there are a couple of good reasons to go with a better grade collet (regardless if we make it...
  4. Replies
    1
    Views
    1,552

    The main advantage to the ER16 kit is it will...

    The main advantage to the ER16 kit is it will allow you to use standard ER16 collets which are made to clamp every shank diameter from 1/16 to 13/32. On the down side it will add more runout (as...
  5. Replies
    14
    Views
    2,776

    Unfortunately we no longer have bushings for...

    Unfortunately we no longer have bushings for tools. It was quite cost prohibitive to get them made to our spec.



    I am unfamiliar with diamond tools made for trace isolation (which is not to...
  6. Replies
    14
    Views
    2,776

    Have you ever tried tools that are actually made...

    Have you ever tried tools that are actually made for cutting PCBs? I cut 40 IPM at 24KRPM using our 60° with no problem. Stub endmills can go even faster then that depending on the diameter you are...
  7. Replies
    10
    Views
    3,588

    If you are looking for a Vcarve like program the...

    If you are looking for a Vcarve like program the cheapest user friendly one I know of is microCarve (Link). However I think you might have been thinking of Cut2d/Cut3d. For those try CamBam (link)...
  8. Replies
    27
    Views
    9,386

    Did it break while plunging or cutting? ...

    Did it break while plunging or cutting?



    Typically MAX TIR a good tool can take is 10% of the diameter. If you have .003" at the collet face that could be enough at the tip.



    Quite right....
  9. We got contacted by one of our customers about...

    We got contacted by one of our customers about this thread as they couldn't understand how something like this could happen (I think that says a lot about our level of service right there). Attached...
  10. Replies
    32
    Views
    5,971

    I'm not worried about people finding us. I just...

    I'm not worried about people finding us. I just don't want to have to retype the whole thing :p.




    Basically what you want to do is get a magnetic base and a dial indicator. We use these...
  11. Replies
    32
    Views
    5,971

    We use our own product here ColletCare. It has a...

    We use our own product here ColletCare. It has a water displacer, lube, and pit fillers. Actually it has multiple versions of most of those. I would post a link but I don't want to break any of the...
  12. Replies
    32
    Views
    5,971

    In our opinion and experience the best way is to...

    In our opinion and experience the best way is to clean with something that has a steel protector in it. If you don't have a water displacer in whatever you are using to clean the spindle with then it...
  13. Replies
    32
    Views
    5,971

    :eek: Do NOT use alcohol on precision steel...

    :eek:
    Do NOT use alcohol on precision steel parts. We have had customers that have been told to do this with their spindles and tools holders. This causes rust to form in/on the tapers which then...
  14. Replies
    38
    Views
    13,502

    Maybe I worded that badly. I thought that the...

    Maybe I worded that badly. I thought that the code was the same (assuming the same step over and tool size ect..). Apparently that is not the case. I just ran Aspire and it appears that the code is...
  15. Replies
    38
    Views
    13,502

    Other then for previewing the image it won't...

    Other then for previewing the image it won't matter which (ball or end mill) you tell Cut3d, the code will be the same. However, I believe the cutters he was pointing you to would be ball nose.
    ...
  16. Replies
    38
    Views
    13,502

    Dennis , would 5° be too much? If not, we already...

    Dennis , would 5° be too much? If not, we already have one of the tools you asked for.

    http://www.precisebits.com/products/carbidebits/taperedcarve250b4f.asp
  17. Replies
    38
    Views
    13,502

    Currently on the short list for one of our next...

    Currently on the short list for one of our next tools. Let me see if I can move it up.




    We are doing some more types of taper tools soon. Let me see if I can get this considered too. I...
  18. Replies
    38
    Views
    13,502

    Usually people get there via the a little bit...

    Usually people get there via the a little bit smaller approach.

    "I'm using a .0625 but do you have a .0313."

    "My competitor is using a .0313 do you have a .0156."

    "The .0156 is nice but do...
  19. Replies
    38
    Views
    13,502

    :( My toes hurt now:( :p I know a a few...

    :( My toes hurt now:(

    :p

    I know a a few places that have .0625. But how about .005" :cool:

    With a human hair for comparison.
    151479
    151480
  20. Replies
    38
    Views
    13,502

    We don't sell compression bits for reasons I wont...

    We don't sell compression bits for reasons I wont go into.

    .250" bits
    http://www.precisebits.com/products/carbidebits/deepreach250f2f.asp...
Results 1 to 20 of 20