Search:

Type: Posts; User: Hayes Rutherford; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. This and a couple of larger versions using the...

    This and a couple of larger versions using the same machined brass laser pointer have served me well. The cameras and monitors are so inexpensive now might have to try that route.
  2. Replies
    14
    Views
    2,733

    David, this is a nice set. I asked about the...

    David, this is a nice set. I asked about the slot configuration on a fiber website and in out of approximately 50 replies, only about 5 used the slot. Doesn't matter, many do use the slot and for...
  3. Replies
    13
    Views
    1,466

    Nice rolling pin for sure. One thing that was...

    Nice rolling pin for sure. One thing that was pointed out to me by a pastry chef is the amount of pressure you can apply with a tapered pin is much greater than a typical straight 12" one with...
  4. Dean, here is still another hood. It simply...

    Dean, here is still another hood. It simply sticks in between the ways and hangs on the wall when not in use. I went 6" to a gate and wye and can use just the top inlet, just the hood, or both. I...
  5. Replies
    21
    Views
    4,268

    I like that Leo. Going to get some Grolsh next...

    I like that Leo. Going to get some Grolsh next time in town and start to empty them. :)
  6. Replies
    34
    Views
    4,804

    John, back pointing is a term used by filers when...

    John, back pointing is a term used by filers when referring to the process of grinding or filing the back of the tooth point as a specific operation. (I resharpen the back of the tooth only on 3tpi...
  7. Replies
    34
    Views
    4,804

    A year?? I usually change out after 4 hours max...

    A year?? I usually change out after 4 hours max of green wood processing (Highland Hardware 3tpi, .032 included) Of course a grain of sand could make that 4 minutes.
  8. Replies
    34
    Views
    4,804

    Timberwolf also has a 3 tpi, .032 blade that only...

    Timberwolf also has a 3 tpi, .032 blade that only comes in 3/8". My experience is that it outperforms the Highland Hardware. Maybe not "hands down" but I "back point" my blades usually 3 times...
  9. Replies
    62
    Views
    10,827

    What Dale said.

    What Dale said.
  10. Replies
    5
    Views
    1,555

    I'm about 1-1/2 hrs. north of Coeur d Alene and...

    I'm about 1-1/2 hrs. north of Coeur d Alene and the whole area is pretty much conifer forest. I get urban wood occasionally and that can vary just like anywhere.
  11. Replies
    31
    Views
    4,606

    Bill, I have that tool. It is beefy and very...

    Bill, I have that tool. It is beefy and very adjustable at the same time. Mine is adjusted for the transition area of steep sided calabash type bowls and doesn't get changed but is ready when the...
  12. Scott, you might look into the Grizzly G0835. ...

    Scott, you might look into the Grizzly G0835. I've only seen it mentioned in the new catalog and guessing it will be less than the G0800. Should make a heck of a bowl lathe.
  13. Replies
    89
    Views
    22,071

    Prashun, I have never turned on the Laguna....

    Prashun, I have never turned on the Laguna. Someone I know asked me what my opinion of the Laguna 18-36 was so I did some research. Looking at the assembly drawings, I found that the 18-36 uses the...
  14. Congratulations on the Laguna 1836. I had under...

    Congratulations on the Laguna 1836. I had under the lathe storage on a Powermatic that started with a basic shelf, then a tool box. Presently I am liking no shelf or storage under the lathe in trade...
  15. Replies
    23
    Views
    6,597

    Still another description of French polishing...

    Still another description of French polishing that is pretty good. Somewhere in the article is a photo of the "vapor trail" that is left when things are happening right. ...
  16. Replies
    10
    Views
    2,464

    Reed, why not just hang a platform from the...

    Reed, why not just hang a platform from the ceiling with a cable you could adjust? Some turners already have pulley systems for living heavy blanks.
  17. John, can't say I've ever seen anything like it. ...

    John, can't say I've ever seen anything like it. I can sure appreciate the work involved and it is really a masterpiece.
  18. Replies
    15
    Views
    3,630

    Its obvious the one in the first photo doesn't...

    Its obvious the one in the first photo doesn't work right for the situation. The guage is tilted and the reading is skewed. I like the Ellsworth method because its simple and you can create a gauge...
  19. I noticed what I first thought to be a knot when...

    I noticed what I first thought to be a knot when slabbing a log on my bandsaw mill, then noticed it was grey in the middle with a copper ring around it. Later I determined that it was a copper...
  20. Replies
    16
    Views
    3,585

    I don't think you are missing anything and make...

    I don't think you are missing anything and make perfectly good sense.

    I have 25" swing and felt as you do that there was no need for a steady that could accommodate that. I built mine so it...
  21. Replies
    6
    Views
    2,110

    Sounds like a Texas Toothpick or a version of.

    Sounds like a Texas Toothpick or a version of.
  22. Replies
    23
    Views
    4,612

    Was just thinking it was about the time your...

    Was just thinking it was about the time your decorated lathe would appear. Will have had mine a year in February. Don't know if I will decorate it but might clean it up and treat it to a coat of...
  23. I was wrong on that . Went to Oneway website...

    I was wrong on that . Went to Oneway website and apparently they have Pro PM as well. Maybe by Crown??
  24. Jason, Pro PM are Crown, Oneway gouges are M42

    Jason, Pro PM are Crown, Oneway gouges are M42
  25. Freehand, just rest your hands/fingers on the...

    Freehand, just rest your hands/fingers on the platform.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4