Search:

Type: Posts; User: George M. Perzel; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.04 seconds.

  1. Hi Brad; I do not like baltic birch- lousy...

    Hi Brad;
    I do not like baltic birch- lousy engraving, poor contrast.
    For 20 years or more I have been using different suppliers of luan ply with mixed results- cheap $15 for a 4x8 sheet
    Current...
  2. Replies
    0
    Views
    1,260

    Lens Ripoffs

    Hi Guys;
    Eighteen years ago I bought my first laser, a Laserpro Mercury, a good machine but limited bed size, for about $27K with lenses costing about $300 each
    .
    Nine years ago I bought a dual...
  3. Replies
    3
    Views
    1,615

    Exchange CN5 and CN6 plugs on controller board-...

    Exchange CN5 and CN6 plugs on controller board- all OPK
    Best regards;
    GM Perzel
    Laserarts
  4. Replies
    3
    Views
    1,615

    Jerome; I looked at that and can't find anywhere...

    Jerome;
    I looked at that and can't find anywhere to switch them. Not sure how RDCam decides which is which.
    Thanks
    Best regards;
    GM Perzel
  5. Replies
    3
    Views
    1,615

    RDCam V.8 Change Laser ID's?

    Hi Guys;
    I am running RDCam v.8 on a twin head 130 watt/head Quantam laser (new) and, after much confusion, found that the RDCam software
    has switched the ID's of the heads. machine Laser 1 is...
  6. Replies
    4
    Views
    1,397

    Tony-thanks Got it Best regards; GM Perzel

    Tony-thanks
    Got it
    Best regards;
    GM Perzel
  7. Replies
    4
    Views
    1,397

    Hi Mike; I am no longer actively selling wood...

    Hi Mike;
    I am no longer actively selling wood thins but do have some cherry, beech, and basswood in different widths and lengths.
    Let me know if you ever need any as I can put together a USPS flat...
  8. Replies
    4
    Views
    1,397

    Reflections

    Hi Guys;
    It's been quite a while since I last posted here. In thinking back, it's been almost nine years since Rodne Gold did his "Marco Polo" thing and ventured into mainland China to investigate...
  9. Replies
    12
    Views
    5,226

    Hi Les; Water input on the bottom of the tube...

    Hi Les;
    Water input on the bottom of the tube and output on the top??
    Best regards;
    GM Perzel;
  10. Indeed a bad control card- laser power supply...

    Indeed a bad control card- laser power supply trigger from control card locked in "ON" position.
    Best regards
    GM Perzel
    Laserarts
  11. I pulled the laser control connector (CN6) from...

    I pulled the laser control connector (CN6) from the RDLC320A control card and the problem went away. It appears that the laser trigger signal is stuck on the "on" level.
    Will change the control card...
  12. Changed the power supply- still have same problem...

    Changed the power supply- still have same problem
    Best regards
    GM Perzel
    Laserarts
  13. Thanks Doug- good idea Best regards GM Perzel...

    Thanks Doug- good idea
    Best regards
    GM Perzel
    Laserarts
  14. Shenhui Twin Tube Laser- One Tube On Constant

    Hi Guys;
    I am having a problem with the Shenhui laser- twin 80 watt tubes.
    Tube 1 laser power is on continuously, when the Laser switch is on -even when the control swutch is off.
    I thought the...
  15. Replies
    2
    Views
    830

    Hi Kev; Thanks- did that many years ago-short...

    Hi Kev;
    Thanks- did that many years ago-short cable was defective almost from day 1.
    Best regards
    GM Perzel
    Laserarts
  16. Replies
    2
    Views
    830

    Shenhui Laser Issue

    Hi Guys;
    I have a Shenhui 1580 Dual head laser which uses the RDL 320-A controler and RDcam 5.0
    The other morning when I turned it on I got a "communication error"on the RDcam program on the...
  17. Bought a Shenhui twin 80 watt 1580 eight years...

    Bought a Shenhui twin 80 watt 1580 eight years ago for total of $9300 of which $2600 was for shipping/clearance by freight forwarder. One original tube still going and 2nd tube replaced two years...
  18. Engrave it with a Co2 but slower than usual to...

    Engrave it with a Co2 but slower than usual to insure the letters are deeper. Then fill with Elmer's white wood filler-let dry and wipe of excess.
    Best Regards,
    George
    Laserarts
  19. Replies
    9
    Views
    1,868

    I'm with Dave- have a tube in my machine for 5...

    I'm with Dave- have a tube in my machine for 5 years and no degradation in power or any other issue. The tube on the other side lasted 4 years+. originals were both RECI's.
    Best Regards,
    George...
  20. Replies
    18
    Views
    3,967

    Hi Charles; If you make multiples of the same...

    Hi Charles; If you make multiples of the same product you may want to consider a dual head system- incremental cost is small and output doubles! Best Regards, George Laserarts
  21. Replies
    3
    Views
    1,381

    Hi Frank; I have a pair of new mirrors for the...

    Hi Frank;
    I have a pair of new mirrors for the Mercury1 which I purchased awhile ago and never used. Send me a PM and we can work something out.
    Best Regards,
    George
    Laserarts
  22. Replies
    11
    Views
    2,906

    Hi Tim; Scan gap of .042 equates to 600 dpi per...

    Hi Tim;
    Scan gap of .042 equates to 600 dpi per my chart. This is much too high and details get blurred.
    Best Regards,
    George
    Laserarts
  23. Replies
    11
    Views
    2,906

    Hi Tim; Most critical thing when engraving...

    Hi Tim;
    Most critical thing when engraving photos is to make sure your photo resolution matches your scan gap- and DO NOT resize your image after processing.
    I use Photoshop to set the image size...
  24. Hi Guys; OK-here ya...

    Hi Guys;
    OK-here ya go334695334696334697334698334699334700
  25. Bert/Kev; Thanks-got it Best Regards, George...

    Bert/Kev;
    Thanks-got it
    Best Regards,
    George
    Laserarts
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4