Search:

I have had to release the paper film from some old sheets and was advised by my supplier to wipe over with petrol and when it dries the film will release.
It works for the paper film. Safety is an...

Hey thats mine, I was asked before you. HaHa......

First ensure that you have the correct acrylic, does the laser cut the samples cleanly that you have.
I have found that I cut or engrave acrylic at 35% speed and 80% power.
Check your piping and...

Hi Bert; Just downloaded the top and found open vectors.
I highlighted the complete drawing went to Join Curves with the tick removed and then hit apply.
Nearly all the vectors closed there is one...

The easy way is to draw a box in Corel and move it around the drawing and you will find all of the areas that you want.

Got to be lucky some time.. So easy to place the new address on the sign at the shop.

I have found that there is no way to weld three vectors tha way you wish to. I cut and join the outer lines and then group the whole drawing to keep the centre areas to the outer vector.343710

I believe that there is a limit that they will accept Paypal payment of $25,000.oo. This is apparently set by the Chinese Government. I feel safe to use Paypal and not my credit card.

I bought my machine 4'x3' from a US supplier and found the machine was made in china, That was Ok. The tube (90watt) failed after three years, the Us cost would have been $1500 plus freight to...

I had to replace the 110 volt air pump and air extractor and found the pump was available from the aquarium suppliers. There are a range of pumps available,
I got the largest one that he had. It...

I Varnish all of my timbers before lasering or CNC carving. This allows the area lasered to be paint filled or painted with out bleeding.

Hi Ron: Also when checking the water flow check that there is no broken glass in the tube, Mine broke where the tube of glass came from the inner tube to the exit tube. Water flowed but not where it...

Does the black wipe out when you us the damp cloth?

I have a 9060 80 watt FS Laser unit, A couple of hic hups setting it up. I am in Australia and parts of the machine was 110 volt and others in 240 volts, not stated when i purchased it. Bert Kemp...

I cut a lot of MDF and removed the grate as well, vast improvement to the air flow. I am the only one to clean the area so I consider it safe.

If your machine has a red beam dot check the lens near the exit point of the tube, the lens could be blocking part of the laser.

I think the fan for the electrics was a little dusted up. I cleaned the fan and there has been no problems with the machine, I am completing a couple of large jobs at this time 16 hours worth of...

The safety switch reset this morning and the machine is working well, spoke to GWeilki who sold me the last tube and they said that the machine is working properly, unknown why it stopped. possibly...

I have had this FS Laser machine for 3 years and it has worked well only 1 replaced tube last July. Friday it stopped after 1 hour of engraving, no power and the safety switch will not reset. After...

Hi, I am starting to do bread boards in Aussie, I have joined a man shed and use old step treads and use a wood thickness-er to get the height that I require and engrave the message in this board and...

Good catch, Bill

I have used a thin sheet of rubber with a water soluble glue before. Used to cut out template for sand blasting onto marble for head stones.
Cut the design on your vynal cutter and weed the parts...

I have used boxmaker and I use Corel. The side that you wish to make flat I:
1. Weld the vertical and horizontal corner lines together and then join.
2. remove all the lines and corners from the...

If the fitting is 10 mm you can use air compressor hose as I did when I changed the cooling system of my machine.

Sorry to all members, I have to learn to use the internet before asking stupid questions.
Thank you.