Search:

Type: Posts; User: philip labre; Keyword(s):

Page 1 of 12 1 2 3 4

Search: Search took 0.02 seconds.

  1. Capn Eddie Castelin has a couple videos on how to...

    Capn Eddie Castelin has a couple videos on how to make a parting tool. One from an edger blade and the other from a saws all blade.
  2. Replies
    12
    Views
    2,713

    i made one urn and some keepsakes using weight at...

    i made one urn and some keepsakes using weight at the time of passing. I should have had enough volume, but did not realize that after the illness takes its toll on the body, what remains is high ash...
  3. Replies
    15
    Views
    3,303

    I used walnut oil on my daily used mills. Been...

    I used walnut oil on my daily used mills. Been several years and still fine. I think they also get refreshed from the hands natural oils with use. The walnut oil held up better than salad bowl finish...
  4. Replies
    8
    Views
    1,648

    What Josh said. Keep the 3ph and get a VFD.

    What Josh said. Keep the 3ph and get a VFD.
  5. Replies
    8
    Views
    1,649

    Looks like a lightning strike. Watch for ring...

    Looks like a lightning strike. Watch for ring shake. Had that problem in a soft maple that was struck. Beautiful wood.
  6. Replies
    5
    Views
    1,838

    Scott, I purchased the metal cores for the...

    Scott, I purchased the metal cores for the bangles from wildwood designs, the bangle guy. They have a tutorial on how to do their bangles. Once I get a chance to restore my metal lathe, I hope to be...
  7. Replies
    5
    Views
    1,838

    Bloodwood peppermill

    Went down into the shop intending to clean up a bit. Got distracted. 10" bloodwood with an aluminum band, CA finish and a Crushgrind mechanism. Did this before with copper and walnut, but I felt I...
  8. Replies
    7
    Views
    1,776

    I did some curly ash and maple that I rounded...

    I did some curly ash and maple that I rounded wet, dipped the ends in anchor seal and put in my bowl kiln. Had no checks. Tried it with some square chunks and had lots of checking. Maybe I just got...
  9. Replies
    10
    Views
    2,153

    I like it John. Look forward to see where you go...

    I like it John. Look forward to see where you go from here.
  10. Replies
    8
    Views
    2,273

    Cribbage guy is the template that I used, the...

    Cribbage guy is the template that I used, the four track nonlinear. 492 dang holes to drill. If I were to make a few of them I think I would make a circle jig to use on the drill press with a...
  11. Replies
    12
    Views
    5,528

    I built one but didn't put a fan in it and the...

    I built one but didn't put a fan in it and the bowls closest to the bulb tended to dry a bit too quick. Otherwise worked well.
  12. Replies
    8
    Views
    2,273

    Great idea Thom! I'll have to check the diameter...

    Great idea Thom! I'll have to check the diameter of the centering bits I have. Hayes, I bought a template for the holes because I liked the nonlinear idea. Thought about turning pegs, but I'm so out...
  13. Replies
    8
    Views
    2,273

    Cribbage board

    I haven't had much time to turn because I've been way too busy with my day job. Finally had some shop time couple weeks ago and wanted a new cribbage board. Curly maple finished with antique oil....
  14. Replies
    9
    Views
    2,166

    Another for "Art of the Turned Bowl". Really...

    Another for "Art of the Turned Bowl". Really helps you understand bowl design.
  15. Replies
    18
    Views
    4,261

    +1 for Doctor's Woodshop. Not as dark as...

    +1 for Doctor's Woodshop. Not as dark as Mahoney's.
  16. Replies
    39
    Views
    7,376

    Had a 14" Grizzly and the lower axle wore out....

    Had a 14" Grizzly and the lower axle wore out. Bought an old American made Powermatic to replace it. Put new bearings in it and you'll have a heavy, solid saw for a reasonable price and some extra...
  17. Replies
    24
    Views
    4,769

    Citrol by Schaefer works great at cleaning...

    Citrol by Schaefer works great at cleaning equipment. Excellent degreaser and won't harm paint.
  18. Replies
    17
    Views
    3,489

    Check out penturners dot org for a wealth of...

    Check out penturners dot org for a wealth of knowledge regarding pen turning. The amount of info in the library alone will keep you busy for a while.
  19. Glad you had a good time Jeff. I ended up working...

    Glad you had a good time Jeff. I ended up working late that night and was quite disappointed I missed your demo. I was really looking forward to it. Guess I'll have to wait for the news letter.
  20. Replies
    15
    Views
    2,084

    Congratulations Marc!!!

    Congratulations Marc!!!
  21. Great find guys! There should be more marking on...

    Great find guys! There should be more marking on the lathe because I believe the Henry Prentiss badge was the distributor, not the manufacturer, and they shut the doors in 1942....
  22. Replies
    13
    Views
    3,929

    Exotic blanks.com

    Exotic blanks.com
  23. Replies
    16
    Views
    2,845

    I've only made the Crushgrind mechanisms and use...

    I've only made the Crushgrind mechanisms and use a 1" brad point bit with a 1/2" shaft extension for the through hole. I've also recently got a good deal on a Woodcut Milldrill which cuts both...
  24. Replies
    20
    Views
    5,962

    I prefer Tru-oil. It's a polymerized oil like Leo...

    I prefer Tru-oil. It's a polymerized oil like Leo recommended, but it's linseed oil based. It was developed for gunstocks and is quite popular with luthiers as well. Just wipe light coats on with a...
  25. Kallenshaan woods has a laser blank that is a...

    Kallenshaan woods has a laser blank that is a tuxedo. Maybe they have a blank that has something relating to the brides interests too.
Results 1 to 25 of 288
Page 1 of 12 1 2 3 4