Greg....Are you getting excessive vibration on the saw?
I would put LockTite on all four bolts before
torquing them down.
Andrew
Type: Posts; User: Andrew Minear; Keyword(s):
Greg....Are you getting excessive vibration on the saw?
I would put LockTite on all four bolts before
torquing them down.
Andrew
How reassuring is that? I have Grizzly machines and that is a wonderful response from Shiraz. It shows true dedication from a great company.
Andrew
If you are using 3/4" material, which I would for speakers, the pin nails aren't going grab enough to hold. The 23 gauge pin nails only go up to 1 3/8" long.
Shooting any nail into MDF is probably...
Say you have an outside corner to crown. That should be two 45° cuts. If The left leg is square at 45° and the right leg veers away at 47°, then an angle finder wouldn't give you a true reading. It...
"Get busy living, or get busy dying."....Inspirational Quotes by (Stephen King, The Shawshank Redemption)
Andrew
Some cases I do not store the tool in, because, there aren't a lot of little parts to go with the tool and the tool itself doesn't need protection, like corded drills etc. Those cases are gutted of...
If you drive a drywall screw through the top layer of paper...it has gone too deep. The drywall screw gun can be set to just dimple the screw into the paper so the first coat of mud will bury it.
...
You just gotta love Shiraz taking the time to post a response, very cool.
Andrew
Conduit and metal boxes are up to code. It is sort of an industrial look, which you may like. Rent a conduit bender for the install. One advantage is that you can easily change the layout, if needed....
That bench sure does look rock solid with those massive stretchers. I wish I could get the good Doug Fir here. Nice bench.
Andrew
The Corian should work well. It is shaped with woodworking tools, so, if you happen to hit it with the TS blade, no big deal. It is fairly slick, which would help with feeding. It is somewhat...
The real advantage to building the cabinets yourself is quality. The materials, thicknesses and fastening techniques you use are easily as good and better than top tier custom cabinets....
James.... That's a really nice shop. The 20 X 32 size is not quite twice the size of mine, so, I could really settle down in one that big. When I dug the trench for my electric, I plotted the...
Have to agree with Scott about the Delta 35-7657. I removed a Forrest WWII from my Grizz 1023ZX and replaced it with the Delta, just to try it out. The rips in maple, plywood and particle board were...
Wow Craig, that is a beautiful piece. What a great way to showcase that incredible mahogany slab.
Andrew
Bob, could you elaborate on that? Don't think I've heard of that kind.
Andrew
That is quite a rig. And, if you have Phil Thien's complement....you done good, son.
Andrew
I don't go to the shop everyday because it takes an hour to heat up with an electric heater. Usually I wait until I have 3-4 hours of work planned out, or, if I just want to clean up for an hour I...
Funny you should mention that, mine IS still in the box. :o
I'll open it up today and see if it will fit on the truck shelf where my Hitachi 10" SCMS is now. Might have to alter the shelf to get...
Which are the good 12" SCMS blades?
Andrew
Rick....try working up a test piece of the red oak to show LOYL. Sand to 180 grit, fill the pores....I like Constantine's or Pore-O-Pac. And finish with a water based urethane. The color is quite...
In my experience, the correct way to handle this is to skim the ceiling with drywall compound. Bring it out a couple of feet and feather the edge. Check it with a straight edge. The variance should...
Bruce, I had a similar problem with an armoire door. After installing magnetic catches at top and bottom door corners, the warp has been contained for 12 years with that tweak. Good luck.
Cliff, the certainty of a mistake is in my work somewhere, and, it's 5:00 here. Thank everyone for the input.
Good idea, I didn't think of that one, thanks.