Search:

Type: Posts; User: Kendall Landry; Keyword(s):

Page 1 of 3 1 2 3

Search: Search took 0.01 seconds.

  1. The owners manual will tell you what size circuit...

    The owners manual will tell you what size circuit to use. If it were me, I'd put at most a 30amp breaker and at least 10ga wire and 30amp recepticle/plug for a 5hp motor unless the manufacturer says...
  2. Replies
    18
    Views
    37,402

    Ive seen HVAC guys using one to do their work in....

    Ive seen HVAC guys using one to do their work in. Drills might be the only tools they were using. Not sure.
  3. Replies
    9
    Views
    3,969

    If the pith of your 4x4 isn't in the middle, it...

    If the pith of your 4x4 isn't in the middle, it won't dry square. Might bugger it up alittle, might not.
  4. Your right Rick, I didn't lookup that particular...

    Your right Rick, I didn't lookup that particular code. Do you have it? The information came from an Inspecter. A very nice older gentlemen who is a woodworker like his father was. We talked for some...
  5. Replies
    15
    Views
    2,924

    Elbow room. I like it Don. Lookin good.

    Elbow room. I like it Don. Lookin good.
  6. Where I live, the breaker can't be rated highter...

    Where I live, the breaker can't be rated highter than the wire or the receptical.
    Your friend is correct.
  7. Replies
    23
    Views
    11,165

    Dan, your talking to the OP about electricity....

    Dan, your talking to the OP about electricity. I'm talking to him about safety.
    If by the slimmest of chances that rigged up cord catches fire, you know who
    the Fire Marshal is going to blame.

    ...
  8. Replies
    23
    Views
    11,165

    Extention cords have a temperature rating. The...

    Extention cords have a temperature rating.
    The heavy duty 15 amp may have a lower temp rating than the 20 amp.
    Even though 12 ga. should be good enough to do 20 amps at 40 feet,
    the 15 amp cords...
  9. Replies
    13
    Views
    7,300

    Cypress would also be nice.

    Cypress would also be nice.
  10. Replies
    16
    Views
    3,392

    I know how it feels not to be able to do the...

    I know how it feels not to be able to do the things I used to.
    Arthritis
    Sorry I wasn't there to help you.
  11. Replies
    21
    Views
    3,927

    I don't believe the size matters as much as the...

    I don't believe the size matters as much as the amount.
  12. Replies
    21
    Views
    4,448

    Look at that big veneer arch. Very nice work.

    Look at that big veneer arch. Very nice work.
  13. Replies
    5
    Views
    2,100

    Let it dry and it cuts/routes fine. Thats too...

    Let it dry and it cuts/routes fine.
    Thats too much routing to do. :eek:
    Put your worm drive on it. That's what I'd do.
  14. Replies
    12
    Views
    2,984

    Reducing is for multiple michines. Same size all...

    Reducing is for multiple michines. Same size all the way for one at a time.



    Yes but will be hampered by the 5" restriction. Might get some chip build up in the lines.



    Considering...
  15. Replies
    8
    Views
    3,184

    I'll try Mr Plesums. I have a CV 1800. With one...

    I'll try Mr Plesums. I have a CV 1800. With one port open, it filters the entire shop. I used a dado to cut half laps yesterday for about 4 hours. Filled my can twice. Nothing in the filter cleanout....
  16. Replies
    31
    Views
    9,948

    You could do something like this. Their is a...

    You could do something like this. Their is a Clear Vue cyclone in there. 5 horse. Walls are insulated. Two vents. One on top next to the light is bout 11 inches square. It makes a U-turn and goes to...
  17. Replies
    36
    Views
    12,222

    hehehe You've prolly seen some code...

    hehehe

    You've prolly seen some code violations yourself. I've got some pics of some absolutely scarry things poeple have done to their electrical systems! Way beyond violation.:eek::eek::eek:
    ...
  18. Replies
    20
    Views
    7,550

    This has 3 ribs under the 3/4" + hard board top....

    This has 3 ribs under the 3/4" + hard board top. A few more ribs and a sheet under the top would make a nice torsion box. Good for assembly. Its got 4" lag bolts under legs for hieght ajustment. 51"...
  19. Replies
    36
    Views
    12,222

    Even if nothing ever happened, I couldn't look at...

    Even if nothing ever happened, I couldn't look at myself in the mirror knowing I didn't get electrical work I'd done inspected. My family lives in that house! Got to remember whats important.
    Can't...
  20. Replies
    20
    Views
    2,770

    Thats pretty stuff Greg!!! What did you cut the...

    Thats pretty stuff Greg!!! What did you cut the timbers up with?
  21. Replies
    24
    Views
    2,899

    hehehe, I wouldn't say urban myth but it was dry...

    hehehe, I wouldn't say urban myth but it was dry enough on the outside to take the stain. What you see in the pic weighed around 250 pounds. It will prolly lose bout 75 or so.
  22. Replies
    190
    Views
    91,513

    Gitter done Jim !!!:D

    Gitter done Jim !!!:D
  23. Replies
    24
    Views
    2,899

    Hi Marc, I brought this PT pine home soaking wet....

    Hi Marc, I brought this PT pine home soaking wet. A few days later the surface was dry enough to stain. Came out great. Oh and gorilla glue likes it wet. :D
  24. Replies
    3
    Views
    1,991

    Your shed was too hot. The wood was drying too...

    Your shed was too hot. The wood was drying too fast.
  25. Pretty work !!!

    Pretty work !!!
Results 1 to 25 of 57
Page 1 of 3 1 2 3