Search:

Type: Posts; User: Bob Herpolsheimer; Keyword(s):

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    11
    Views
    6,486

    Raco produces one. Stock # is 915C (this is an...

    Raco produces one. Stock # is 915C (this is an industrial cover) and should cost around $4.
  2. Tim, I beleive it can be done but may be way...

    Tim,

    I beleive it can be done but may be way more work then it's worth. I think you will need to do a motor start that is controled with low voltage for the DC. You could then pull something...
  3. Replies
    8
    Views
    9,328

    Izzy, Cold weather start must include proper...

    Izzy,
    Cold weather start must include proper ballasts as well as tubes. It is true that T8 lamps will start at zero degrees but below 60 you may only get 1/2 the lumens (actual amount of light)...
  4. You guys may have already tried this but there...

    You guys may have already tried this but there are different grades of ballasts. For example, Advance ballast has the REL4P32SC & the REB4P32SC. Both will run the exact same thing, 4 T8 tubes. The...
  5. Hey Jason, go to www.lithonia.com...

    Hey Jason,

    go to www.lithonia.com they have a rep locator that will give you who sells these in your area. A good fixture is a tandem strip # TC 2 32 MVOLT 1/4 GEB10IS. It's economical and the...
  6. Replies
    9
    Views
    1,857

    Could you be talking about the disconnect...

    Could you be talking about the disconnect required in fixtures now? If so, there should be a small sack with the other part in it (this is to hook to your power supply cord). My guess is that there...
  7. Replies
    24
    Views
    4,237

    John, I would stay with an open fixture...

    John,

    I would stay with an open fixture (easier to clean) but John Keeton is correct. Get a a high output fixture. If you get one with a ballast that has a high ballast factor you can get a T8...
  8. Replies
    7
    Views
    1,972

    Plugmold puts out a 6' strip that has outlets...

    Plugmold puts out a 6' strip that has outlets 6,12 or 18" on center. The price is a little better. A 6" on center will run around $60-70.
  9. I would wire a power supply cord to each fixture...

    I would wire a power supply cord to each fixture and then just put up nail-on boxes with a single receptacle in each box. Pig tail the receptacles on one circuit. This way you are able to...
  10. Replies
    22
    Views
    6,496

    Hi Rusty, I have the 22114 but I think the...

    Hi Rusty,

    I have the 22114 but I think the amount of assembly will be similar. Mine came in 1 box. It was a steel pallet which adds a lot of weight to moving but also made the it impossible for...
  11. Replies
    15
    Views
    30,522

    Nick, I just picked up a plastic roll from...

    Nick, I just picked up a plastic roll from Platon. It is the same type of plastic that Dricore puts on the osb. It comes in a roll that covers 175 square ft and it supports 1000 lbs per square foot...
  12. Replies
    11
    Views
    2,765

    Not much Jason. I do have a 1950's vintage home...

    Not much Jason. I do have a 1950's vintage home lathe and I have been meaning to start turning but it's on that list with 100 other projects that I want to start. You know the old story, it comes...
  13. Replies
    11
    Views
    2,765

    I made my own. Since you have to buy the garbage...

    I made my own. Since you have to buy the garbage can anyway it seemed easier to add $10 worth of pvc fittings and make one. By the way, you live in a GREAT town.
  14. My vote is on the switch too. I too have a HF...

    My vote is on the switch too. I too have a HF that was hooked to a remote switch. When mine died I pulled the switch and just wired it direct and haven't had a bit of trouble since.
  15. Replies
    26
    Views
    4,650

    GREAT JOB MICHAEL!!!. That is a fun one to build....

    GREAT JOB MICHAEL!!!. That is a fun one to build. I built the same one for my son. I agree with Bill to sign the piece. It would be great that your great grandchildren can look at the piece and...
  16. Replies
    21
    Views
    3,698

    Hi Brian, I don't have any pics but I can...

    Hi Brian,

    I don't have any pics but I can tell you what I used. I have the green light weight drain PVC. There is an adaptor for conversion from this pipe to heavier wall pvc. This adaptor...
  17. Replies
    13
    Views
    2,952

    Hi Steve, I have a home made. I was friends...

    Hi Steve,

    I have a home made. I was friends with some electricians at a heating/air company so I got one of their throwaways. It's pretty easy. I started with the filter and picked out what I...
  18. Replies
    5
    Views
    869

    Anyone from Lincoln?

    Hello everyone,
    I am looking for a show of hands from the Lincoln NE area. I’m looking to see if there is any interest in meeting. Nothing formal, mainly swapping ideas techniques ect.
  19. Mike, What Tom is saying is correct. A...

    Mike,

    What Tom is saying is correct. A couple other points to consider.. if you get a stand alone stand-by (one that is on a pad outside your house) they will most likely come with a emergency...
  20. $300 is a fair price. Spend the money, this is...

    $300 is a fair price. Spend the money, this is designed to do a specific task safely. There are cheaper ways of doing this but when you look at the big picture $300 is cheap compared to a new...
  21. Thanks Guys for the good ideas. Greg, I got...

    Thanks Guys for the good ideas.

    Greg, I got the idea from here about calling Delta. There is a thread about the same problem. I called Delta customer service, I explained to the lady that I...
  22. Looking for some help on a Delta 22-560

    Hi Everyone.
    Using this great resource I see that I am not the first one this has happened to. The drive pulley on the cutting head has come loose and I burned up a belt. I contacted Delta and the...
  23. Hi Jason, Go to an electrical wholesale...

    Hi Jason,

    Go to an electrical wholesale house. Use 14-3 SJ cord with 515 plug. Both together should run you less than $20. The 14-3 should be about the same size as what you have on the saw...
  24. Replies
    16
    Views
    2,474

    Great link Ed, Thanks!!!

    Great link Ed, Thanks!!!
  25. Hey Adam, UNL has a Foresty Dept withing...

    Hey Adam,

    UNL has a Foresty Dept withing their Extension Division over on east campus. I bet they could help and if not direct you to someplace that could.
Results 1 to 25 of 38
Page 1 of 2 1 2