Search:

Type: Posts; User: wayne Jepson; Keyword(s):

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    14
    Views
    7,733

    Finished up this infill recently an used gun...

    Finished up this infill recently an used gun blue. I really like the look of it and I will definitely use this finish again. Here is a link to another forum post....
  2. Replies
    3
    Views
    958

    Smaller bent back mitre plane

    Here is the second of the three bent back mitre smoothers I am making. 6" long and 1-1 1/4" wide with 1" wide blade bedded at 22 degrees. Infill is boxwood with danish oil finish. I have been looking...
  3. Replies
    22
    Views
    4,327

    Thanks for the suggestions George, ever since the...

    Thanks for the suggestions George, ever since the first infill I made from a St James bay kit you have shared your knowledge and made suggestions on how to take my work to a higher level. Thanks for...
  4. Replies
    22
    Views
    4,327

    First Bent Back Infill Mitre Plane

    Been real busy in the shop the last few weeks before Christmas doing "real" woodworking. Made a coffee table and almost finished a dining room table for my wife's cousin for her wedding present. I...
  5. Try finding an old power planer or jointer blade....

    Try finding an old power planer or jointer blade. Should work for what you need to do. I have made marking knives from them before.

    Wayne
    http://infillplanemaker.blogspot.ca
  6. Replies
    10
    Views
    1,865

    Thanks George, I will give that a try on the next...

    Thanks George, I will give that a try on the next one. Will have to pick up a clean wheel though.
  7. Replies
    10
    Views
    1,865

    Thanks to all for all the complements. Sean good...

    Thanks to all for all the complements. Sean good luck on your plane.
    , make sure you post pictures.

    Wayne
    http://infillplanemaker.blogspot.ca
  8. Replies
    10
    Views
    1,865

    Block plane sized infill smoother.

    Finished up this block plane sized infill today. It is 6" x 1-3/4" with a 1-3/8" wide 3/16" thick blade bedded at 47-1/2 degrees. Infill is east indian rosewood.

    Wayne...
  9. Replies
    11
    Views
    1,602

    A couple for my till

    This weekend I finished up a couple of infills for my plane till. A boxwood mitre smoother and a small east Indian block plane sized smoother. More pics at the link below....
  10. Replies
    4
    Views
    1,389

    Hi Ken, please post more pics of those wonderful...

    Hi Ken, please post more pics of those wonderful planes.

    Wayne
    http://infillplanemaker.blogspot.ca
  11. Replies
    31
    Views
    6,867

    I can't wait for the wooden plane blades in this...

    I can't wait for the wooden plane blades in this material too. I use the LV wooden plane blades in my infills and they are great.Made from this material sounds like they will be even better. Hurry up...
  12. Replies
    8
    Views
    3,800

    Hi Corey , pm me if you seriously want to build...

    Hi Corey , pm me if you seriously want to build one. I can help you locate materials and I'm more than willing to share my experiences I have so far in making them. I believe im located close to you....
  13. If George is too busy I can make them. Follow...

    If George is too busy I can make them. Follow this link to pics.

    http://forum.canadianwoodworking.com/showthread.php?46074-Made-some-infill-lever-cap-screws

    Wayne
  14. Replies
    19
    Views
    3,954

    Hi everyone. Recently i received a very...

    Hi everyone. Recently i received a very respectful message from a member of a woodworking forum. The message advised me that may not be a good idea to make planes that incorporate designs that are...
  15. Replies
    19
    Views
    3,954

    Infil plane

    Pm sent to you Bob. Thanks
  16. Replies
    19
    Views
    3,954

    Higher res pics and you tube link

    231081231082231083231084231085231086231087


    http://www.youtube.com/watch?v=e8txjZQYzxA&feature=channel&list=UL
    http://www.youtube.com/watch?v=rbcwXdd5-iY
  17. Replies
    19
    Views
    3,954

    Thanks everyone for the amazing amount of...

    Thanks everyone for the amazing amount of interest in this plane and the complements. I have made a few planes in the past but when I used Konrads planes at a show a little while ago I was totally...
  18. Replies
    19
    Views
    3,954

    Hi Peter, no i am a woodworker with some...

    Hi Peter, no i am a woodworker with some metalworking knowledge. I plan to do a production run of 5 of these planes. I made all components from scratch except the blade. It was purchased.
  19. Replies
    19
    Views
    3,954

    New infil plane

    Totally inspired by Konrad Sauers K series planes that I played with a couple weeks ago at a show here is a prototype that is almost complete. 6 1/2 inches long smoother with blade bed of 52.5...
  20. Replies
    4
    Views
    2,447

    Here's the link to one I did. ...

    Here's the link to one I did.

    http://www.sawmillcreek.org/showthread.php?138099-Another-stanley-infill&p=1403078&highlight=#post1403078
  21. Replies
    13
    Views
    6,368

    Just finishes a similar dresser. I just used...

    Just finishes a similar dresser. I just used several coats if shellac on the inside. Dries fast and does not make everything inside the drawer smell.
  22. Replies
    15
    Views
    4,827

    Coincidence....saw one advertised today. I had...

    Coincidence....saw one advertised today. I had never seen one before this.

    http://ontario.kijiji.ca/c-buy-and-sell-tools-equipment-Mortise-Machine-W0QQAdIdZ258314679
  23. Replies
    12
    Views
    2,664

    Hi Marc, sounds like you got bit by the same bug...

    Hi Marc, sounds like you got bit by the same bug as me. Bought a small mill and lathe and started building infills. Done just a couple so far but plan to make many more. They work so well when...
  24. Replies
    9
    Views
    3,700

    I have thought about a norris type adjuster but i...

    I have thought about a norris type adjuster but i am just trying to figure out how to make. I am not a machinist so any help anyone can provide would be helpful.
  25. Replies
    9
    Views
    3,700

    A few more pics including the start of another...

    A few more pics including the start of another plane and the machines i use to do it.
Results 1 to 25 of 32
Page 1 of 2 1 2