Search:

I believe that NW-20 is the model number. Do a Google search for Northwood NW-20 planer.

I also ran into the issue that Curt mentioned when I got a Delta tenoning jig to use with my Craftsman saw. It appears that some companies make the bar .750" wide, and others make the slot .750"...

The FCC has a web site that will show you which stations are available in your area, and show the relative signal strength you can expect. You plug in your address to get the info. Be aware that most...

I have had good results with Behr drywall primer and sealer number 73. I have found that if you have sanded your drywall mud so that there are no high spots, and then prime with this primer, it will...

I have never had a problem with Minwax poly drying. Many years ago when painting some window sash with oil based paint in my basement shop, the paint was not completely dry after two days. I finally...

I replaced a 70's Kenmore disposal with an Insinuator disposal and it connected to the existing Kenmore flange without any problems. The flange looked like this.
...

Fastcap makes electrical box trim rings in both single and double box sizes, and in three colors. The electric outlet stays installed in the wall, and the trim ring covers the cutout in the back of...

You could use a corner block to compensate for the different heights of the base board.

http://www.homedepot.com/catalog/productImages/400/40/404062b7-763b-4182-81f3-644a79f59236_400.jpg


...

They do make extruded aluminum inside corner trim for the joint between the two pieces of formica. Years ago it was typically used to add a formica back splash to a counter in a kitchen. Do a Google...

The November 2015 issue of Wood Magazine has plans for a Pint-size Rocking Chair which you could build or scale for size dimensions.

323486

The old wood doors are very heavy, and if it has torsion springs, there are usually two. If one spring breaks the second spring can't overcome the weight of the door. I had one spring break on my old...

I have used connector nuts to install threaded rubber pads on a friend's pool table. I used a forstner bit to drill a hole in the leg and used epoxy glue to install the nuts. Connector nuts are...

A friend of mine sucessfully heats his two car attached garage with a 240 volt Fahrenheat electric heater, he is located near Canton Ohio. Before installing the heater, we blew in fibergalss...

I would use Loctite Power Grab Construction Adheasive. I installed aproximately 60 feet of oak vinal base board in a friends house several years ago using Power Grab and only had to use four finish...

If you only need a small amount of the 3M adheasive, you can find it at some Home Depot stores in a 3 ounce tube for $6.47. I have used the standard caulk tube of the 5200, and once opened it will...

From the picture, it apears that the shelf is at least 36" long which would cover three studs if on 16" centers, and the three vertical sections of the shelf would give you stability. You could use...

The Home Depot stores in NE ohio carry some Azek products, and also have other brands of PVC trim. I have used their brick mould and garage door stop without any problems.

Azek...

I recalled seeing a reference to an inlay material in a recent post, a google search lead to this. I have never used any of this type of material, but it may be what you are looking for.
...

The reason the lathe dosn't keep running when the start button is released is that the holding contacts on the starter are not connected. The manual shows the micro switch drawn as a single pole...

Boaters use a gelcoat repair kit to fix small defects in their boat hulls. The kit has a polyester resin, six tubes of color, and a tube of hardner. It is basically like a colored epoxy, and the...

Many counter fabricators can make a side splash that is scribed to fit over and around the post formed counter top. Since the side splash is 3/4 inch thick, there can be a gap between the counter top...

I have seen a kitchen exhaust fan intermittantly trip a GFCI outlet, and eventually had to rewire it to a different circuit.

Home Depot also carries some Liberty hardware in multi packs.
European 110 degree full overlay hinges ( I have used these hinges, and they work OK, though not the same qualtity as Blum)...

David, you have built a very nice system, I like the automated operations shown in your videos. Just the other day I saw a similar system from Sommerfeld's advertised in a magazine. Their ad showed...

I ordered the T2 fence from Tools Plus in March for my 1970s Craftsman table saw. The price was $149.97 plus $6.50 shipping, and it was shipped promptly via UPS.