Search:

Type: Posts; User: Terry Sparks; Keyword(s):

Page 1 of 4 1 2 3 4

Search: Search took 0.01 seconds.

  1. Take the switch apart and clean it. If it woks...

    Take the switch apart and clean it. If it woks and you still want to buy a new sander, let me know, I'm in the market for one.
  2. Replies
    14
    Views
    3,801

    Just wondering if you have a crosscut sled for...

    Just wondering if you have a crosscut sled for your table saw? I found that I didn't need a sliding mitrer saw after building one and also saved myself a few hundred bucks in the process.
  3. Replies
    105
    Views
    24,410

    Hi Jeff, I too have space problems with my garage...

    Hi Jeff, I too have space problems with my garage shop and storage for a full complement of kitchen cabinets will not wotk for me either. I'm in the planning stage of building my cabinets and in...
  4. Replies
    10
    Views
    5,089

    I made my laundry room and kitchen cabinets with...

    I made my laundry room and kitchen cabinets with very good results using Marc Sommerfelds Shaker set (among others) using two identically set up router tables. It was an easy set up and it was easy...
  5. Replies
    9
    Views
    14,765

    Also take a good look at the Kreg Pocket Hole...

    Also take a good look at the Kreg Pocket Hole Jigs if you are going to build face frame cabinets. You can find many YouTube instructional videos of their jigs to get you started, including how to...
  6. Replies
    16
    Views
    1,883

    John, something to consider... Paper that old...

    John, something to consider...

    Paper that old could start to tear fairly soon at the creases just by turning the pages, and will start to fade if exposed to direct sunlight. It might be...
  7. Thank you and add my name to the list!

    Thank you and add my name to the list!
  8. Replies
    20
    Views
    4,497

    "He needs to replace his dead Brand X 3/8" corded...

    "He needs to replace his dead Brand X 3/8" corded electric drill."


    With that in mind, I would think just about anything on Craigslist should do.

    No need to over think the problem.
  9. Replies
    10
    Views
    3,854

    Another way to solve this problem is to "borrow"...

    Another way to solve this problem is to "borrow" a couple of emery boards from your wife, place them on the piece you want clamped and then place the clamp on the emery boards. I have used this...
  10. Replies
    14
    Views
    13,793

    My chop saw station is 40" high with 8' of table...

    My chop saw station is 40" high with 8' of table on one side of the saw and 5' of table on the other side. The reason I made the station 38" high is so I can park my table saw (34") and wheeled tool...
  11. Replies
    7
    Views
    1,440

    I thought about buying this unit just to re-sell...

    I thought about buying this unit just to re-sell on Craigslist, but then realized in doing so would be more hassel than it's worth.
  12. Replies
    10
    Views
    2,305

    No need to trash an entirely good motor, I don't...

    No need to trash an entirely good motor, I don't know what the HP of your unit is, but as long as the collet is still good, I would be inclined to recycle the motor to be used as a shop made disk...
  13. Replies
    20
    Views
    4,748

    For dovetails, I have two PC 890's set up, the...

    For dovetails, I have two PC 890's set up, the first router has the dovetail bit and the second router has the straight bit installed. Call me lazy, but after I got my setup dialed in, and for the...
  14. Just a wild guess here but, are you retired?

    Just a wild guess here but, are you retired?
  15. Replies
    9
    Views
    3,787

    Michael, All you need to do is re-apply the...

    Michael,
    All you need to do is re-apply the Evaporust on your table saw and use some 0000 steel wool or 400 grit sandpaper. After working it in for just a few minutes, let it rest and repeat once...
  16. Replies
    10
    Views
    34,256

    My thoughts also, and to add, I don't see the...

    My thoughts also, and to add, I don't see the need for the tops of your boxes to be cut perfectly level, a simple light sanding will take care of any rough spots. And again,as mentioned above, the...
  17. I have 4 or 5 of Marc's router sets and like all...

    I have 4 or 5 of Marc's router sets and like all of them. I also have his old table as well as his newer aluminum table and his system is what I used while learing to build cabinets. Marc's system is...
  18. Replies
    8
    Views
    3,480

    Heck, for the price of all that what do you have...

    Heck, for the price of all that what do you have to lose? It will get you started with using rough sawn wood and when you decide to upgrade to a better unit, I'm sure you can re-coop your $57.13...
  19. Replies
    8
    Views
    3,480

    First thing I would do is find out what a new set...

    First thing I would do is find out what a new set of knives will cost, I'm guessing they will cost more than the price of the jointer.
  20. It's really not that hard to figure out, as far...

    It's really not that hard to figure out, as far as the different hinges and slides. just google "drawer slide videos" and you will get several good lessons on installing drawer slides. It's the same...
  21. I cut the last tape that broke on me at the 6"...

    I cut the last tape that broke on me at the 6" mark, and it now resides with my storage bins of screws and bolts and is used for sizing the wayward screws that need to be put back in their correct...
  22. Replies
    13
    Views
    3,610

    I'm a former owner of a Omnijig for a reason,...

    I'm a former owner of a Omnijig for a reason, they are a pita.
  23. Looks like is sucks to me, just what it's suppose...

    Looks like is sucks to me, just what it's suppose to do....;)
  24. Replies
    6
    Views
    2,222

    I have been using more and more reclaimed lumber...

    I have been using more and more reclaimed lumber over the last few years and that has saved me alot of money, especially when it's very cheap and quite often free.
  25. Allen, here is the correct link to the thread...

    Allen, here is the correct link to the thread mentioned in my previous post.

    http://sawmillcreek.org/showthread.php?t=136395&highlight=dust+collectors

    You can also do a search of "Dust...
Results 1 to 25 of 84
Page 1 of 4 1 2 3 4