Search:

Type: Posts; User: Mike Schuch; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    8
    Views
    3,868

    The plastic part is actually unscathed, it is the...

    The plastic part is actually unscathed, it is the aluminum inner part of the guard that actually cracked and is warped all out of shape. I tried beating it into submission but that just extends the...
  2. Replies
    8
    Views
    3,868

    I broke my Dewalt DW705 miter saw.

    The blade guard on my Dewalt DW705 12" compound non-sliding miter saw cracked when I dropped it. Everything else seems to be in good shape. A replacement guard is going to cost me $100. I can buy a...
  3. Replies
    12
    Views
    6,243

    Take a look at this thread for instructions on...

    Take a look at this thread for instructions on how to fix the speed controller.

    http://www.routerforums.com/general-routing/26952-8529-porter-cable-wont-run-seeking-suggestions-2.html
  4. Replies
    11
    Views
    2,802

    366442 Starting to take shape.

    366442

    Starting to take shape.
  5. Yep, this is what I do to. Press down on the way...

    Yep, this is what I do to. Press down on the way down then release and press to the right on the way up.
  6. Replies
    8
    Views
    1,748

    I agree, it sounds exactly like the start...

    I agree, it sounds exactly like the start capacitor is bad. If not then possibly the relay is stuck open for some reason but much more likely the start capacitor.

    3ph motors are much more...
  7. Replies
    9
    Views
    3,415

    When I used my old powermatic fence I seriously...

    When I used my old powermatic fence I seriously considered buying a second one, sans rails, and butt it against my existing fence attaching the two fences with a panel so the fence would always be...
  8. Replies
    11
    Views
    2,802

    The glue up fits just about perfect! 366072

    The glue up fits just about perfect!

    366072
  9. Replies
    10
    Views
    3,032

    My RAS table hits me right above the belt which...

    My RAS table hits me right above the belt which works perfectly for me. Too low and I end up doing a lot of bending over to line up the blade with the cut.
  10. Replies
    11
    Views
    2,802

    Second glue up. The Two part epoxy didn't hold...

    Second glue up. The Two part epoxy didn't hold as well as I had hoped so I reverted to Gorilla polyurethane glue.

    365922
  11. Replies
    11
    Views
    2,802

    I found getting a pretty good hexagon is pretty...

    I found getting a pretty good hexagon is pretty easy... getting a perfect hexagon is a headache. All my corners are within 1/10 of a degree and still my hexagon jig didn't turn out perfect. The jig...
  12. Replies
    9
    Views
    3,415

    I have a 60's Powermatic 65 with the same fence. ...

    I have a 60's Powermatic 65 with the same fence. I always measured the front and back. Then I bought a used Vega fence and no longer have to measure the front and back. Later I got a powermatic 71...
  13. Replies
    12
    Views
    2,134

    I have a Paslode fuel powered brad nailer... I...

    I have a Paslode fuel powered brad nailer... I will always grab my pneumatic brad nailer when practical. For an occasional base board the Paslode beats hauling out the compressor but for the most...
  14. Replies
    11
    Views
    2,802

    Building a hexagon?

    My daughter asked me to build a hood for her hexagon aquarium. I need a hexagon frame to build the rest of the hood on. The pieces of the frame will be about 1" tall by 1 1/4" wide.

    I started by...
  15. Replies
    70
    Views
    12,980

    I usually do the same thing but I let go before...

    I usually do the same thing but I let go before the peices make it all the way through the planer.
  16. Replies
    18
    Views
    2,826

    If your just going to paint them I would look at...

    If your just going to paint them I would look at repurposing some from used furnature. Thrift store or habitat for humanities store.

    If they are going to be painted it easy to fill a few nicks...
  17. Replies
    13
    Views
    2,248

    A three phase motor controller can easily be...

    A three phase motor controller can easily be re-purposed as a single phase motor controller by simply only using 2 of the three legs (You have to choose the two legs that power the contactor coil). ...
  18. Replies
    8
    Views
    1,612

    I would highly reccomend a Rockell / Porter Cable...

    I would highly reccomend a Rockell / Porter Cable 505 half sheet sander. I own 3 of them with 150 / 180 / 220 on them. They are great for covering big areas quickly and will last forever. My...
  19. Replies
    7
    Views
    1,467

    I have owned a table or two with that type of leg...

    I have owned a table or two with that type of leg bracket. I tend to think of them as kind of cheap... but that is because the tables that came with them were cheap. The tables with those brackets...
  20. 359249...

    359249
    http://www.grizzly.com/products/Shaper-Cutter-1-Bead-3-4-Bore/C2056 - $39.95

    Or is this what you are looking for?

    359250...
  21. Replies
    14
    Views
    5,718

    I too love OWWM's and have a shop full of them,...

    I too love OWWM's and have a shop full of them, most of them restored. I used to hang out at OWWM.org quite a bit to share my passion but the moderator over there is pretty rude. It has been a year...
  22. Replies
    24
    Views
    7,259

    I had a real nice router table, motorized lift...

    I had a real nice router table, motorized lift and all. I built it with my father and then inherited it when he passed. I used it about equally as much as my ancient Walker turner 3hp 3/4" spindle...
  23. I have never owned a combination blade. My...

    I have never owned a combination blade. My Powermatic table saw is pretty much always wearing a rip blade (Usually Freud) and my radial arm saw is pretty much always wearing a Freud ultimate cut off...
  24. Replies
    5
    Views
    3,189

    Thank you guys for the feedback. I knew I could...

    Thank you guys for the feedback. I knew I could rely on this site for good answers! :-) I think I will just go for the 5 hole version, a 2 pack of the aftermarket pads are cheap and get good...
  25. Replies
    5
    Views
    1,567

    I wouldn't use the table for milling on a drill...

    I wouldn't use the table for milling on a drill press. But it would be handy for precisely positioning holes or making a row of precisely spaced holes all in a line.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4