Search:

Going to be building a game cabinet for my kids playroom and want to use some integrated finished end panels to match the drawer fronts. I have built shaker style panels before and used 1/2 inch ply...

I live in Northwest Florida, Panama City area. There was a guy I used in the past but he moved out of state.

I have been using the Freud glue line rip and ultimate crosscut blades on my table saw for the past few years and they are i need of sharpening. With no nearby place to have them sharpened I was...

I bought a pallet of drops and cutoffs from advantage lumber that was supposed to be all white oak but it has a fair amount of red oak pieces mixed in. I am using the white oak to make some end...

i just used some OSMO Top oil for walnut tree slice cheese board that I made for my sister and I really liked it. It is food safe, smelt a lot like Tung oil to me. Pretty easy to apply.

I had the earlex 5500 to start out with and it worked great. I started out spraying GF white poly and then some Target coatings, pigmented and clear. I found a good deal on a FUJI Mini mite 3 on...

I have watched a few River table videos on youtube and several of the used Rubio Monocoat for the finish. Never used it myself but it sure looked nice on youtube!

In my very little experience with epoxy I found that packing tape worked better than painters tape. I just filled some cracks in a walnut slice and it worked pretty well. I covered the entire top...

It slows down right when I feed the board in and then goes back to normal speed so it doesn't have to do with length of the board. As far as depth of cut I am only moving the wheel maybe 1/8 of a...

The feed of the board slows down

Upgraded from a porter Cable planer to a used DeWalt 735. Flipped the blades and replaced the broken drive belt. Overall it runs great and I get very little to no snipe. Problem is that when I run...

Just finished a cypress table for my screened porch, some sun exposure but no rain. I would love to leave it natural and let it grey overtime but with three boys I need something that will protect...

Ok. I will borrow the xl. I ordered some sipo stock today. What length would you recommend? I ordered 12mm stock. I was going to use the domino for the top glue up to help with alignment. What...

Going to bulding a table top for my back porch and have a few questions. I am going to put bread board ends on it and was planning to use the smaller domino machine as I can borrow it from a friend....

Thank you all so much for the input. I have not heard back the customer yet to see if the rings went away. I have some em9300 that I was going to spray over the em6000. I left a message for Jeff...

Made some walnut placemats for a customer and 1 week after she picked them up she was calling about rings left from cups. Finishng schedule was:
2 thin coats BLO each side
Sealcoat 50:50 with DNA...

Pretty sure old masters makes both a 100% Tung oil and a Tung oil/varnish blend. I don't have any ideas on how to remove it though.

Looking for some advice on using some older Target Coatings products. I have some em8000 and em6000 that have been opened and stored in my garage, temp usually around 75 never below 60. They are...

It dried overnight flat on a glue up rack made up of two PVC pipes screwed to some 2*4 pieces. The piece is going to be used as a tray for a friend's coffee maker so I doesn't stain the marble...

Just glued up a 18x30 panel last night. It is made up of about 10 pieces. I glued up 5 pieces into two panels and then those together. Now the big panel has about a 1/16 to 1/8 bow. I know I can...

Thanks for the advice. Jim and Prashun - would you have any pictures of any walnut pieces that you have finished? Jim - your "Continent" douglas fir top was AMAZING!

This is the look the customer if asking for.

I am going to be making some placemats out of walnut for a friend and would love some finish advice. I have a Fuji mini mite 3 with a pressure cup gun. I have some Target em8000 conversion varnish...

Saw some cabinets in a friends house where the tops of the trash pullout fronts had a metal trim piece screwed to the top to protect it. Does anyone know a source to get this from? I have attached...

I figured that would be the case. Any ideas on how to get the really sticky bits out? Would pouring some lacquer thinner though the crack help?