Search:

Type: Posts; User: Shane Copps; Keyword(s):

Page 1 of 3 1 2 3

Search: Search took 0.01 seconds.

  1. I put R board up behind some OSB in my shop. I...

    I put R board up behind some OSB in my shop. I offset the seams and it made a world of difference (shop is an old garage/apartment building) in cutting the air flow through the room. I haven't...
  2. Replies
    7
    Views
    1,478

    This seems to be the issue. The work piece works...

    This seems to be the issue. The work piece works up the tailstock center and walks away from the drive center and then it spins or tears out.

    Thanks
  3. Replies
    7
    Views
    1,478

    Ok- This tells you how new/how long it's been...

    Ok- This tells you how new/how long it's been since I have done any turning.

    What I seem to have from your descriptions are a Drive Center with a point and 4 spurs. and for my tailstock I have a...
  4. Replies
    7
    Views
    1,478

    Another newbie question

    OK guys,
    First, thank you for helping me with the centering issue. I remounted the log on the lathe (SS) like you guys told me to, Then as the lathe was chattering around a little vs. jumping...
  5. Replies
    13
    Views
    2,478

    Thanks guys. I had the SS set as low as it...

    Thanks guys.

    I had the SS set as low as it would go (700)- I do have the older headstock. I was pretty scared to see the log go flying(it took off away from me) and that is why I'm looking for...
  6. Replies
    13
    Views
    2,478

    Newbie Question

    I turned a little in High School shop class (quite a while ago) and haven't done any since. I am going to try it again but I need some pointers from you knowledgeable folks. I put a log on my...
  7. Replies
    4
    Views
    1,032

    Put up and finished my set of built in book...

    Put up and finished my set of built in book shelves for the office. As I'm not going to be in this house but another year, I didn't want to spend to much money on them. I used shelving for the...
  8. Replies
    13
    Views
    2,951

    Dave, Not trolling, I guess Im just trying...

    Dave,

    Not trolling, I guess Im just trying to get a feel for what everyone else does and hopefully get a better handle on what I want to do.

    I ended up with a BUNCH of saw blades with a...
  9. Replies
    13
    Views
    2,951

    Table saw blades

    Is it worth trying to find someone to sharpen blades? I have a pile of them that I either need to get rid of or get sharpened so I can use them. Sharpening should be cheaper, right?

    Thanks for...
  10. Replies
    6
    Views
    10,765

    Looks good

    Looks good
  11. Replies
    18
    Views
    3,793

    Store Inventory Increase- What to carry

    I'm looking for ideas.

    I am in the process of buying a Hardware/Lumber store in MT and would like some ideas on what to carry. It is a small town (about 2000 people in the county and adjoining...
  12. Replies
    20
    Views
    4,772

    I would use the downstairs as my actual shop with...

    I would use the downstairs as my actual shop with wood storage and some tool/parts storage upstairs. I had almost the same downstairs set up in my old shop (16x24 shop in the back of a 2 car garage)....
  13. Replies
    3
    Views
    872

    Been working nonstop on the garage and shop- put...

    Been working nonstop on the garage and shop- put workbenches on two walls and got some tools put where I can get to them. Now I'm waiting on the electrician to fix the power and i'll be in a lot...
  14. Replies
    9
    Views
    1,946

    Are you doing just the countertop? The whole...

    Are you doing just the countertop? The whole island/cupboard setup?

    I guess without knowing very much about your project or setup, I would start by letting the boards dry out (assuming they are...
  15. Replies
    20
    Views
    11,711

    +1 on the screws- Nails will back out within a...

    +1 on the screws- Nails will back out within a short time.
  16. Replies
    18
    Views
    4,004

    Thank you very much everyone. I really...

    Thank you very much everyone.

    I really appreciate it. I ended up putting up a 5 ft and 3 ft gate in the 8 ft hole. Mostly it will be a walk through with the option of opening it for something...
  17. Replies
    8
    Views
    2,203

    Dennis The new floor is 27x27 roughly. It has...

    Dennis
    The new floor is 27x27 roughly. It has some insulation in it, but I'm putting up some r board and osb as the summer goes on. I plan on painting it white when I'm done.
  18. Replies
    18
    Views
    4,004

    Shawn and David, I can split the one 7-8 ft...

    Shawn and David,

    I can split the one 7-8 ft gate, it would probably work better anyhow. The ten foot gate- I could just make it solid fence as the only real reason I was going to put it in is in...
  19. Got it to work- Thank you guys for all your help-...

    Got it to work- Thank you guys for all your help- appreciate it
    Shane
  20. Replies
    18
    Views
    4,004

    292406292407292408 Here are some pictures of...

    292406292407292408

    Here are some pictures of what I am working with if that helps me get some ideas
  21. Replies
    8
    Views
    2,203

    I messed that up --- the inline pics are of the...

    I messed that up --- the inline pics are of the shop. The attached are of my other current project - Fencing in the yard. I have a question in the woodworking forum for that.

    Thanks for letting...
  22. Replies
    8
    Views
    2,203

    292399292400292401292402292403 I'm trying...

    292399292400292401292402292403

    I'm trying this. Here are some pics of the new shop. It was an apartment building YEARs ago and the floor flooded so previous owners took the floor out and put...
  23. Thanks Rich, I will try that. The next...

    Thanks Rich,

    I will try that. The next question is how do I reduce the file size?
  24. Replies
    18
    Views
    4,004

    Privacy fence gate problems

    I am putting up a privacy fence and have gotten to the gates. I had planned to build a square frame, put a 45 board from the bottom of the open side to the top of the hinge side and then mount it to...
  25. Not able to get pics to the post? Maybe I'm doing something wrong

    How do I upload pictures? I Reply to Post, Go Advanced, Manage Attachments, Add Files, Browse for the pic. and hit Upload. All I get is Upload failed. Am I doing something wrong? Can someone give me...
Results 1 to 25 of 72
Page 1 of 3 1 2 3