Search:

Type: Posts; User: Greg Jurrens; Keyword(s):

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    5
    Views
    2,410

    Santa Rosa Lie Nielsen Event

    Did any other creekers go to this event at David Marks shop.
    Greg
  2. Replies
    11
    Views
    4,260

    Planing quartersawn Bubinga

    I'm having a terrible time planing a 1/4 sawn bubinga cabinet top. The wood is very rowed. I've tried a low angle jack and a 65 deg. jack with about the same results. Any ideas would be appreciated....
  3. Replies
    8
    Views
    2,688

    Try this link . There's always good ideas and...

    Try this link . There's always good ideas and inspiration here.
    http://www.pritameames.com/archives-2.html
  4. Replies
    7
    Views
    2,110

    That' a great look. Very sleek and contemporary.

    That' a great look. Very sleek and contemporary.
  5. These drawers were made by laminating the front...

    These drawers were made by laminating the front and then planing flats on the ends that are the same width as the drawer side. Next I cut a regular through dovetail. I finished up by laminating 2...
  6. Replies
    20
    Views
    10,101

    Here's a photo of my Krenov plane. I used ash for...

    Here's a photo of my Krenov plane. I used ash for the body,purpleheart for the sole and a Hock iron.
  7. Replies
    21
    Views
    2,802

    I think Wenge would look great

    I think Wenge would look great
  8. Replies
    15
    Views
    3,734

    Bore the stretchers with a forstner bit the same...

    Bore the stretchers with a forstner bit the same diameter of the leg and then use loose mortise and tenon joinery.
    Greg
  9. Replies
    23
    Views
    3,205

    I really like the design and the combination of...

    I really like the design and the combination of Jatoba and Maple. What joint did you use between the legs and aprons?
  10. Replies
    15
    Views
    9,812

    I converted an old Shopsmith into a slot...

    I converted an old Shopsmith into a slot mortiser. I used some 8020 inc. extrusions and linear bearings to make a sliding table. I use end mills for cutters and it works great.
    ...
  11. Replies
    8
    Views
    6,423

    Hi Jerry, Thanks for the info on Sacramento. The...

    Hi Jerry, Thanks for the info on Sacramento. The wood sources seem pretty slim there. I live south of Eureka. I get most of my hardwoods at Almquist Lumber in Arcata.
    Greg
  12. Replies
    8
    Views
    6,423

    Sacramento Hardwood Sources

    Does anyone have a good source for exotic hardwoods like Wenge in Sacramento Ca ?
    Greg Jurrens
  13. Replies
    12
    Views
    2,836

    Curved cove cut

    I'm designing a piece of furniture that will have a table sawn cove that would follow a curve. Does anybody have any suggestions or experience in doing such a cut?
    Greg...
  14. Replies
    23
    Views
    44,751

    The best and strongest way to get this joint...

    The best and strongest way to get this joint tight is to get a good fit.
    The easiest way is to slide 120 grit sandpaper backed with packing tape through the joint making sure not to round the...
  15. Replies
    4
    Views
    1,198

    Tom, I made one from an older Shopsmith. I used...

    Tom,
    I made one from an older Shopsmith. I used linear bearings and rails from
    8020 Inc to make a sliding table to mount on the shopsmith table. The quill feed controls the depth of cut, and the...
  16. Replies
    29
    Views
    3,921

    Thanks & Details

    Hi all,
    I want to thank everyone for their much appreciated compliments on my Jatoba blanket chest. I have been an amateur woodworker for about 20 years now. In the past I made mainly small...
  17. Replies
    19
    Views
    38,307

    Here in the mountains of northern California...

    Here in the mountains of northern California where I live there are numerous creeks. When we need a bridge in a hurry we use a scrap railroad flatcar.
    Greg Jurrens
  18. Replies
    29
    Views
    3,921

    Jatoba Blanket Chest Finished

    Here's a photo of the Jatoba chest finished.
    I used 4 coats of Sealacell clear. This finish is almost foolproof. I tried
    this product after seeing David Marks use it on just about everything.
    ...
  19. Replies
    20
    Views
    1,902

    Jatoba chest

    Thanks for all the kind words. Yes it is my own design and I will post more pictures when it is done. Here's a couple more views for now.
    Greg Jurrens
  20. Replies
    20
    Views
    1,902

    Blanket Chest

    This a new blanket chest of Jatoba and curly Maple that is almost ready for finish. It is a combination of solid wood and shop sawn veneer.
    The Jatoba is great to work with and takes a wonderful oil...
  21. Replies
    4
    Views
    2,646

    I have an older unused Shopsmith and my idea was...

    I have an older unused Shopsmith and my idea was to convert it to a horizontal slot mortiser. By using the quill feed and the table height adjustment all I would need is a sliding table. Do you think...
  22. Replies
    4
    Views
    2,646

    8020 Inc Sliding Table

    Has anybody on SMC used 8020 inc. linear motion bearings and track to make a sliding table. I'm thinking about making a horizontal slot mortiser. Any thoughts on thiswould be appreciated.
    ...
  23. Replies
    19
    Views
    1,959

    Jointer gunk

    I got this same Delta jointer from Amazon about a month ago. The clean up is really easy by using Simple Green cleaner at full strength. About ten paper towels and maybe fifteen minutes and I had a...
  24. Replies
    8
    Views
    1,810

    I'll try some baby powder to see if that helps....

    I'll try some baby powder to see if that helps. As for the brand of the sleeves I think that they are "other". What brand of sleeves are you using?
  25. Replies
    8
    Views
    1,810

    Yes I have taken the nut and washer off and have...

    Yes I have taken the nut and washer off and have also slid out the steel spindle.
Results 1 to 25 of 28
Page 1 of 2 1 2