Search:

Type: Posts; User: Chet Parks; Keyword(s):

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    6
    Views
    1,908

    I took a photo copy of my honorable discharge...

    I took a photo copy of my honorable discharge from the Marine Corps into HD and got the discount.

    Chet Parks
  2. Replies
    32
    Views
    4,415

    Great job! I'd like to build one for my daughter....

    Great job! I'd like to build one for my daughter. I've got a whole bunch of cherry just sitting here and this would be a perfect use for some of it. Where did you get the plans, or did you just "wing...
  3. Replies
    17
    Views
    16,279

    I have used white and red oad, cherry and maple...

    I have used white and red oad, cherry and maple scraps to make quite a few blocks. My grandsons don't seem to care what wood it is. They all stack and fall over with the required amount of noise.
    ...
  4. Replies
    23
    Views
    6,261

    Looking at the Carter site and how the unit is...

    Looking at the Carter site and how the unit is installed, I'd say that they are using a small load cell and just measuring the pressure that the blade adjustment spring is exerting on the stationary...
  5. Replies
    4
    Views
    870

    The town of Belvidere, NJ has a simular sized...

    The town of Belvidere, NJ has a simular sized oak, which is a prized tree in the town. This one is located with 1/2 of the trunk in the street. The tree has been hit by cars several times and they...
  6. Replies
    26
    Views
    4,328

    Why spend good money for one, when you can made...

    Why spend good money for one, when you can made one that works just as good, if you have a jointer?

    http://img.photobucket.com/albums/v512/ChetParks/Tools/DSC00380.jpg

    The slice is less than...
  7. Replies
    29
    Views
    3,217

    Great Shop

    I enjoyed looking over your shop. You sure have a good selection of equipment.

    I have the same 18x36 Delta drum sander that you have. I noticed that you have some nice drop down support tables...
  8. Replies
    14
    Views
    3,548

    I use this on all my CI power tool tops. Works...

    I use this on all my CI power tool tops. Works great on MDF also.

    http://www.bwccompany.com/bowlingalley.html

    My local hardware store sells it for $6.99 an can.

    Chet
  9. Replies
    4
    Views
    963

    Belt dressing

    I use this:

    http://www.valvoline.com/pages/products/product_detail.asp?product=32

    You can usually find this a a NAPA Auto parts store.

    Chet Parks
  10. Replies
    26
    Views
    2,760

    HD isn't that much safer

    I was in HD on Monday and stoped just short of an isle and a kid, came around the corner of the isle with a fork lift that had boxes of Barbeques on it stacked two high, the fork was about 8' up in...
  11. Replies
    24
    Views
    9,106

    I bought the Grizzly 6" jointer, 7 months ago and...

    I bought the Grizzly 6" jointer, 7 months ago and within the first month started kicking myself for not spending the extra money for the 8" one. If you are into getting rough cut lumber from a...
  12. Replies
    11
    Views
    1,338

    Nice looking shop. I like the 8"jointer. BUT, how...

    Nice looking shop. I like the 8"jointer. BUT, how come I didn't see any sawdust in the corners and covering some of the equipment?:)

    Chet Parks
  13. Replies
    40
    Views
    4,543

    Here's what I used

    I acquired a shaper with a table that was covered with several years of rust from sitting in a shead with high humidity in the summers. I used this:

    http://www.grizzly.com/products/G1956

    with a...
  14. Replies
    25
    Views
    5,666

    Wax

    The best wax I have found is "BUTCHER"S Bowling Ally" past wax. You can get it at any hardware store. It's 100% carnuba wax and doesn't have the addatives you find in car wax.

    Chet18013s
  15. Replies
    17
    Views
    2,005

    The most used woodworking book I have

    I stumbled accross "The Woodworker's Problem Solver" at Barnes & Noble last year. It's edited by Tom O'Malley and published by Reader's Digest. It has no plans, but is an assembly of solutions to...
  16. Replies
    7
    Views
    928

    Or , you could just get a MAC. They support two...

    Or , you could just get a MAC. They support two monitors right out of the box.

    Chet Parks
  17. Replies
    20
    Views
    3,696

    If I were closer, I'd buy the planer in a heart...

    If I were closer, I'd buy the planer in a heart beat, maybe sooner.

    Chet Parks
  18. Thread: Outhouse ?

    by Chet Parks
    Replies
    20
    Views
    3,236

    When I was a small kid, we lived in rural...

    When I was a small kid, we lived in rural Nebraska. We had a two hole'r out house. I can remember spending some "quality time" sitting and talking with Dad out there. --One of the memories our kids...
  19. A new mouse trap?--or bisket replacement??

    Has anybody seen these in the US yet?

    http://www.enlock.com/index.html

    Chet Parks
  20. Replies
    19
    Views
    2,186

    Helped me, Dave, and I didn't ask the question. ...

    Helped me, Dave, and I didn't ask the question.

    What I have been wondering is there any easy way to show small rounds and fillets in SU, especially ones that are about 1/8 to 1/4"? I have just...
  21. Replies
    12
    Views
    14,168

    Check here: http://www.batteryrebuilders.com/...

    Check here:

    http://www.batteryrebuilders.com/

    Chet Parks
  22. To Todd & Jonathan, Is there any chance that a...

    To Todd & Jonathan,

    Is there any chance that a link exists where we could get a copy of the notes, PDF, or other hand outs from this woodworking session? It sounds to interesting to not try to...
  23. Replies
    10
    Views
    4,084

    Have you checked the Grizzly website? They have...

    Have you checked the Grizzly website? They have all the parts (new and old equipment) and instruction manuals on the site for downloading. I purchased a new 6" jointer from them last year and your...
  24. Replies
    24
    Views
    12,786

    I got a used 22-540 last year and was bothered by...

    I got a used 22-540 last year and was bothered by the snipe problem also. I built this planer table and after some playing, totally solved the snipe problem.
    ...
  25. Parks Here's the jpg file. (double click on...

    Parks

    Here's the jpg file. (double click on image to enlrge)

    Chet
    38153
Results 1 to 25 of 31
Page 1 of 2 1 2