Stephen-
That is a wood - metal bandsaw made in probably the 90's. The transmission in the base is the only difference between the 28-303 and the 28-203 listed above. Check the transmission for...
Type: Posts; User: Dan Boschen; Keyword(s):
Stephen-
That is a wood - metal bandsaw made in probably the 90's. The transmission in the base is the only difference between the 28-303 and the 28-203 listed above. Check the transmission for...
Jerry-
Here you go.
http://www.owwm.com/files/PDF/Delta/1951-PM-1739.pdf
http://www.owwm.com/files/PDF/Delta/1959-8Jointer.pdf
http://www.owwm.com/files/PDF/Delta/1972-8Jointer.pdf
Other than sharpening the whole set, the only way I know to continue to use slightly nicked knives is to very slightly adjust one knife sideways so that it will knock off the ridge that the other two...
Dump the jointer pal and check out
http://video.google.com/videoplay?docid=-572604587960322121&hl=en
It takes a little time on the first try, but the results are excellent.
I've got three of these and I've got to say that they cannot be beat.
http://1manstand.com/
They are very steady and tolerant of any droop of materials.
John-
I believe the detergent is the problem. With washing soda, I've had small parts fizz like crazy and clean well. I use a 12V battery charger with anywhere from 2A to 10A of current flow with 6...
John-
Go to www.owwm.com. Specifically for Craftsman publications,
http://www.owwm.com/MfgIndex/Detail.asp?Tab=Publications&ID=222
Good Luck.
Dan Boschen
Amarillo, TX
We'll it's probably either this one
http://www.owwm.com/files/PDF/Delta/1949-PM1535.pdf
or this one
http://www.owwm.com/files/PDF/Delta/1955-PM-1736.pdf
and should have the cutterhead...
I was using the Fenner Drive Power Twist Belt (red belt). I use them on all of my other tools with single groove sheaves, but I saw an improvement in my Unisaw when I switched from the link belts to...
That's right. Chances are the 1951 Unisaw has the 1725 rpm motor which has a 5.25 inch sheave, which takes the 4L290 or A27 belt. A Uni with a 3450 motor (like your saw) has a 3.25 inch sheave which...
The main things IMO are size and weight. I use my 314 for cutting down 1/2 inch sheet goods and it's a lot easier to handle than my 7.25 inch Bosch. I also have a 6 inch PC Saw Boss which I use for...
My saw did the same thing from the factory. I don't know why they overfill it according to their instructions, but I filled it per the instructions and have had no issues with it and no heat buildup...
I've got a 7529 and I've had nothing but problems with it. It will hardly run a 1/4 inch straight bit when cutting a slot (at only 1/8 - 1/4 in depth!). The speed runs all over the place and the...
Here's what I did with my Unisaw:
http://pages.suddenlink.net/dbosch/outfeed.pdf
I needed a way to roll my saw around just like you. I can roll the saw around with the outfeed deployed or not....
Don't junk it as this scroll saw has many features that others don't. If you look at the lower chuck, you will see two locations in which to clamp an object - one flat and one round (actually it's a...
It is the standard Delta 14 inch bandsaw either wood or wood/metal version. Serial number indicates 1950 birthdate. Go to:
http://www.owwm.com/files/PDF/Delta/1946-14BandSaw.pdf
for an owner's...
Don't let the step stop you from storing tools on it. I've got the same setup in my garage and I use a 24 x 24 x 1/4 inch steel plate that I use as a ramp to push the tools up onto the step. I push...
John-
I think your 37-220 is a late 60's - early 70's model. The sheet metal base, plastic handles on the cranks and badging are similar to my US made model which is a 1973 model. The Canadian...