They played this video at church this morning before the start of service. I can relate to the guy who says "I got dozens of dollars", I wish it were more, but these tools are too expensive.
Type: Posts; User: Doug Palmer; Keyword(s):
They played this video at church this morning before the start of service. I can relate to the guy who says "I got dozens of dollars", I wish it were more, but these tools are too expensive.
Use a Dynamat type product. It is for sound deadening in automobile trunk and cabin areas. Use the cheaper alternative you can get at Lowes called Peel & Seal. It will say it is for Aluminum Roof...
If you would have just said "Doug is the coolest human" I would have felt much better about myself. But you had to go and throw out the last name too. Now I'm back to feeling like the regular Joe...
I am just in the process of getting the proper tools for doing HFs. Haven't really done any turning to speak of (a couple of small bowls to learn how the tools work), but have been reading like crazy...
+1
I know how to keep my fingers away from that blade, but the a piece of wood coming back at me cost me two broken fingers and a few weeks out of the shop.
Whatever your choice, focus on...
Time to resize the whole project. I just wanted a minature scaled model anyway.
I too ordered mine. It will be here on Monday. Til then, no pictures.
I agree with Tom that it sounds like induced voltage. Induced voltages are of no danger.
I've cut this board 3 times and still too short!
Jim,
Craftsman does make a couple of nice planers.They are not the cheaper units you will find in the stores (they are special order) and they do not sell in $400 range. The cheaper Craftmans do...
To say the price is too high or normal is not possible with the limited information you have given. To cavalierly say it is too high is not informed and is not good advice. There are many things that...
I own or have owned all of the following and rank them in order as listed with best being first. JMO
Milwaukee
Dewalt
Bosch
Rigid
Craftsman
I have just recently started turning with no incidences. I am going to purchase a face shield this weekend before I wish I had. If it happens to the experienced guy, I gotta figure the rookies like...
Thanks Richard, very informative. When you drill the holes how deep to you go? All the way through or halfway or other?
I work as an electrical contractor. We are removing MH lights everywhere and replacing with T8 flourescents. Why? MH are very expensive to operate, take for every to come on, generate lots of heat...
Thanks guys. I appreciate the help.
I am just spurring an interest and appreciate learning from others much better than the school of hard knocks. Steve, I must say looking at some of your work...
Hello All,
I have been lurking for a while and have a question. I have done quite a bit of wood working, but I am just getting into turning. I recently purchased a Nova 1624 and am still learning...
Thanks for the humor! I love it. :)
I have had similar problems with TAPCONs, but have found a method has worked very well for me. I drill the hole as normal, then when inserting the screw, I always run the screw in half way, then back...
If I thought this was my last place and I was going to retire there, I would rip it down and start from scratch.
If I thought I was going to move in 5 or 6 years, I would surface mount everything...
Rick,
There is no problem putting the larger fuses in since you already have the breaker sized to protect the wire. I would not put 20A fuses in. In most cases a fuse will blow much quicker than...
Please understand that there is a difference between "working on" a switch and "operating" a switch. The rules are different as well.
Thanks Charley, I'm not so sure that we have disagreed on anything. I have accepted Peter's original post as accurate. He stated he had 240v 3 phase, not 208 3 phase. He later posted that he also had...
With a three phase 240 volt system, you should see 240 volts between phases. However when you measure phase to ground or phase to neutral you will probably see some odd readings. If I remember...
I knew when I posted this it would open a can of worms. When first approached with this concept by an MSHA inspector I thought it sounded completely backwards. It is difficult for me explain, as I am...