Search:

Looking to build a workbench/assembly table, but not certain how to do it(design wise.) I was hoping some of you could post some pictures of your current setup. I am looking to transform a corner...

I am well awaye of the the safety factors... but when I get the guy to come over from Delta Factory Service, Ill ask him to take a look-see. Its fine for now...

I just checked my email, and realized I had gotten an email back:
.ExternalClass p.ecxMsoNormal, .ExternalClass li.ecxMsoNormal, .ExternalClass...

Hmm maybe Ill end up doing that... just get a cheapo one instead...

I keep all meaty bits 4in away from all sharp bits... Since I realize that my local butcher uses this to size my steaks....

The main reason is the dust port... I try to hook the shop vac up to everything I can.... and that is the only one, besides Festool, that has a round port.. That I have seen.

I also like the...

I left them an email, but they arent getting back to me.

Any other opinnions?

Lol... I must ask what the average lifespan of a Romanian woodworker is? Age 20? 30? I doubt beyond there...

Your right though... if OSHA ever saw that.. the founder would turn over in his...

I got my big old blade running on my 14". It works like a charm. But I am having an issue with the guard. Its fine, at about halfway height and higher, but if I lower it beyond there, it begins to...

I have to ask, what did you use on the angle grinder to do that? I have one myself... but I made the mistake of cutting into a piece of wood once(using as a backing for the metal)... You will never...

Since Mike revived this dead thread, Ill add my 2c...

I would love to have a 42in Bandsaw... I just cannot see myself cutting much that size.... Sure it would work as a good cross cut saw... but...

You dont ness. need to use their band size. Just lower the upper wheel to its lowest point, add 2 cranks on the tensioner, then measure the distance between wheels(Use a string, mark it, then...

Nice work.... I have gotta say... I am jelous... since I am working out of a single car garage...

I was wondering if any of you have had experience with the Sears Evolution Evo Rage?(

I think I want to get a circular saw for my next project(not the saw... making a workbench/Assembly area is...

15ga Nailers in a nutshell, drive thicker nails. So thus they have more power behind them, weigh a tad more(shouldnt be an issue unless you do construction all day lugging them around), and...

No problem Larry.

I would post this in the Neanderthal Section... its mostly people who use only hand tools(with the acception of a drills and such.) You might have better luck there.

I might try a good old fashioned pry bar assuming its nailed to the frame. Else I might very well cut them off with a Sawzall.

I would have to recommend "The Bunker" as one of the worst.... Nothin' worse than Undead Nazis in a bunker with stupid people... I remember it has attrocious acting...


I forget who said it,...

I had a problem with Hewlet Packard a while back myself. I was intrested in putting a new graphics card in. I asked them if it would work. When I asked them for the specifics of my...

60 hours! You must have 10 helpers armed to the teeth with nail guns and shapers...

Does it actually cut? From their web page it appears to be a laser pointer..

Id look for an SCMS.. not a CMS... I did a dado once on a CMS... it didnt look right nor was it functional, since the bottom was rounded, and to get the right depth, you might have to saw through...

It would be nice if they would put actual wheels on things, rather than using those flimsy plastic knobs...

Such as on my Delta Bandsaw.... while the blade is tensioned, it is next to impossible...

Short blade life, but, thats the only way you will be able to get any capacity out of that scrawny thing....

I still dont recommend it... save up and get a Delta, even a Reliant... 14"

Just...