Search:

Does anyone have any experience with this drill press. I want to use it to run a 6" holesaw for cornhole tables. Have tried 1/2" ridgid hand drill and pattern routing bit, Cant hold drill and...

Jeff, I did what u have done with the switches But also wired it so I can use a remote. A transformer and contactor are the way to go because u will have a hard time overamping them. I any one has...

If you have a Home Depot nearby check them, Mine near me had A C grade for 25 a Sheet. I bought a whole skid because I have a guy that I build speaker boxes for that needs around 100 built the next...

I just wired mine with a 24volt transformer and a 90340 relay with a remote switch. I just put it in a box and can turn the system on or off with the remote or with switches i have mounted on tools...

U guys with the mini splits better keep your filters clean the dust from a shop will clog the coil of any ac unit. I have seen some good ones being in the wholesale ac business.

in my shop I...

I went without face frames and just put dust frames everywhere I wanted a drawer or the top and bottom of the cabinet and did not use drawer slides just the slick tape from woodcraft on the dust...

If you use a 120 volt contactor as long as you have the hot on the same leg you can use 3-way switches and a remote for Christmas light to turn the system on or off.

That is the way I have mine...

Thanks for the info. I was measuring the chippers wrong. I also had not thought about a sharpening service

I have a DD208 purchased from Home Depot. I chipped the teeth on 1 1/4" chipper and the 1/8" shipper due to not tightening the arbor nut tight enough and the blades shifting. How much would it cost...

Thanks guys. Do you think I could have the motor rewound as 220 volt single phase?

Friend gave me an old B&D Dewalt 3578 Radial arm saw, Because it was in his way. Does anyone know if I can get a manual and 220 volt single phase motor for this saw?
Thanks

230v 40a contactor with 110v coil and cheap Christmas light remote switch. Also wired in regular switch at tablesaw and planer so I could turn it on without remote.

Chase,
Where in Hahira do you live? I also live there and have a cyclone separator I would be willing to part with. I built on of the Pentz cyclones and put it in front of a Jet DC-1200 Works great.

I am located in Hahira, Ga

I am looking at buying a PC 4210 or 4212 Dovetail Jig. My wife wants me to make some drawers for a closet organizer. The drawers will only be 10" deep.
I am open to other recommendations for a...

Thanks, Al That helps me a lot. I am in the wholesale a/c business and one of my customer's is going to help me cut it out and put it together at his shop today.

Thanks for the info guys. Also would it hurt to put a 6" outlet in the middle instead of the 10", I am going to run it into a Jet DC1200A, and use the separator stand alone with the 1200a in the...

When using Bill's design for a cyclone separator, how for down into the cylinder should the outlet pipe go past the air ramp ? I have looked at all the pictures I could find and can't really see how...

Thanks for the reply's everyone I will look at the Blum site, I just wasn't sure where to get started.

Does anyone know of a guide for selecting cabinet hinges for face frame cabinets?

I'll check into the wynn filter, I have not seen the collector yet my friend dropped it at my house, he says it has a top on it so maybe it already has a cannister. Thanks for the information

I just bought a 1 year old Jet DC-1200 from a cabinet shop for $50.00, But I need to replace the bags. Where can I order the 1 micron filter bags from, and get the best price ?
Thanks

Try looking for 6" pipe at an a/c supply house. I work at one and can sell you the 6" pipe for $4.35 for a 5' piece. You need to check the a/c warehouses they will kill HD and Lowes on price.

I have a PC 690 router and the Pc template guide nut loosens after about 6" of cutting. Does anyone know an easy fix for this or do I need new guides.
Thanks.