Search:

I’m looking to put a dust collection system in my workshop. I have read about different types and requirements and they seem to be all over the map from a Cyclone to a Shop Vac. If anyone can give...

Steve,

Just used your code and got the 5% off. Thanks for the info...

Scott

Hello all,

I'm looking at purchasing the G0453P Planer from Grizzly and saw where you can enter a coupon code. Does anyone know where to find a code. I have look on the web and did not see...

JR,

Good idea, I will give this a try...

Scott

I have a 3” laminated piece of cherry that I need to cut a pattern on. On smaller pieces I will create a template cut the piece on the band saw as close as I can then use the template with a flush...

Peter,

After years of just wearing drug store glasses so I could see the small stuff (a accident waiting to happen) I went to Sams Club vision and they have industry strength safety glasses, they...

I have a Delta table top planner. I have used it for a many years now and it has worked well. Lately I have noticed some small ridges in the boards I would say they are about 1/32 - 1/16 in height...

I just completed a salt water fish stand and a canopy for a 180 gallon tank. The materials are Hickory and Ash and there is no stain. I want a satin type finish but do not want to use poly. Can...

Jeff,

The problem is splintering on the edge of the panel, and I do have a zero clearance fence with a profile insert for the bit. Only on one edge do I have this problem (I assume it is when I go...

Thomas,

Thank you that is what I was looking for


Scott

I saw plans a few months ago on the creek for a children’s marble toy. If I remember correctly it had a sheet of plywood with a thin metallic sheet covering it. PVC was used to cut the channels for...

The tear out is along the edge not at the end of the panel.

The bit for the raised panel is very large 3” The bit comes with 2 bearings a 1 ¼” and 5/8” When routing the panel I start with the end grain and go around the door(end grain, side, end grain, and...

I presently have a Sears router table. It has been ok for now but it does not provide all the features I would like. I want to build a new one and not sure if I should build it into my table saw or...

Thanks for the input, but when I try to shoot a nail I get very little air from the exhaust. It is like it is not enough pressure in the nailer...

Scott

I have a Porter Cable BN125A Brad Nailer. It has been working fine then started to miss fire now and then and would only shoot a brad sometimes now it will not shoot a brad at all. Air pressure is...

Thanks to all who replied. I will take the info from your messages and lay out my plans for my tank stand. I plan to add a lift support for the top so that you do not have to hold the lid or lean it...

:o Looking to build a fish stand for a 125 gallon tank. Does anyone have plans for one? I want to make sure that the base will be strong enough and appreciate any ideas on how to keep it water...

What I failed to mention the blanket chest is from Fine WoodWorking issue 203

I have ordered plans from Taunton Press for a Blanket Chest that is featured in February’s issue 203. What I did not know is that it will take 7 - 10 business days to receive the plans in the mail. I...

Thanks to everyone who replied, as always a wealth of information on this forum, I'm ready for the tree to come down.

Scott

Sam,

Thanks for the info. I will give it a try I will have to keep the wood in my garage and in Florida we get the humidity. But since the tree has to come down anyway maybe I will get some good...

Richard

I'm not very well versed on kiln drying wood. I thought I would resaw the wood in 1" planks and seperate them with a 1/4" rail so they they can be aired on all sides. Do you think this...

I live in central Florida and have a Holly tree that needs to be removed. Has anyone used Holly in woodworking projects? Is this something I should save and resaw some planks. Any thoughts would be...

Cliff,

I agree I must make sure that the blade is centered. When I put a square on the table against the blade I have 1/16 gap at the bottom. I have a Luguna 14 SE and have ceramic blocks for...