Search:

Type: Posts; User: tyler mckenzie; Keyword(s):

Page 1 of 7 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    33
    Views
    20,514

    I own the bench dog, it's solid. I can change...

    I own the bench dog, it's solid. I can change bits above the table (i forget the model number).

    I couldn't recommend it more.
  2. Replies
    11
    Views
    8,065

    I'd suggest a table saw. I have a cabinet saw...

    I'd suggest a table saw. I have a cabinet saw and the ts75, it's a rare day if i go for the ts75 first.
  3. Replies
    4
    Views
    1,655

    tom, it looks great. looking forward to seeing...

    tom, it looks great. looking forward to seeing some finish on it.

    tyler
  4. Replies
    41
    Views
    11,893

    well said peter Nancy, a joint based on...

    well said peter



    Nancy, a joint based on gluing short grain isn't a solution when making a door. This is a forum to learn, and i worry that someone might come to the end of this thread...
  5. Replies
    41
    Views
    11,893

    i saw a door snap in half that was joined with...

    i saw a door snap in half that was joined with biscuits, granted the door didn't have 4 per joint. Biscuits for me have always been an alignment tool.
  6. Replies
    19
    Views
    3,315

    Dan the smaller one is a 14" Walker Turner! He...

    Dan the smaller one is a 14" Walker Turner! He just got a facelift (scroll down a post). The other is a Davis and wells great machine, just started putting it through its paces.
  7. Replies
    19
    Views
    3,315

    That gets you a shop that doesn't need to get...

    That gets you a shop that doesn't need to get replaced or upgraded. My estimate was based on someone who builds for their living. My shop is all used machinery, i've found it's all the little thing...
  8. Replies
    19
    Views
    3,315

    i'd say 25-30 will get you started. Grizzly is...

    i'd say 25-30 will get you started. Grizzly is considered to be on the lower end of the quality spectrum.
  9. Replies
    3
    Views
    2,236

    the turbo is a great vacuum. mine came with a...

    the turbo is a great vacuum. mine came with a hose, two nozzles, rubber nozzle, and a fabric filter. I didn't up grade to the hepa.

    Micheal covered it all, are there any other part you...
  10. Replies
    39
    Views
    15,217

    I just don't see how 30 minutes of my time is...

    I just don't see how 30 minutes of my time is worth the tersa costs.
  11. Replies
    39
    Views
    15,217

    Rod are you talking about the general 130 planer?...

    Rod are you talking about the general 130 planer? My 130 is fully adjustable, and when tuned right is a zero snipe minty machine. It takes some wrenches but its as solid as a 14" planer gets.

    i...
  12. Replies
    8
    Views
    1,867

    looking tight, do you have 8ft on the left side...

    looking tight, do you have 8ft on the left side of the blade?
  13. Replies
    26
    Views
    6,198

    If they work for you why change? Drill bit tear...

    If they work for you why change? Drill bit tear out freaks me out, so i only buy the best, Lee Valley lipped brad points.
  14. my poitras 12" jointer uses jack screws, changing...

    my poitras 12" jointer uses jack screws, changing knifes without them would be a pita.
  15. Replies
    20
    Views
    3,080

    If you can get the board flat, then your...

    If you can get the board flat, then your tolerances are fine.
  16. Replies
    7
    Views
    1,272

    The disposable economy, what a hopeless waste. ...

    The disposable economy, what a hopeless waste. I'd say your money is better spent on a good tool you need.
  17. Replies
    35
    Views
    15,893

    I found a General 130 14" planer. Well built,...

    I found a General 130 14" planer. Well built, very solid for a small machine. Everything is adjustable, so you can dial it into perfection. Lunch boxes are not what i'd deem quality machinery,...
  18. Replies
    5
    Views
    1,531

    you might want to include some more info.

    you might want to include some more info.
  19. Replies
    21
    Views
    5,119

    Did it? Great work. Was there any punky...

    Did it?

    Great work. Was there any punky parts in the maple?
  20. Replies
    28
    Views
    4,178

    every piece i own has been moved with a portable...

    every piece i own has been moved with a portable engine hoist. I've got a few machines weighing in at 1400lbs. I usually dismantle, then go from the main casting. What's your heaviest machine?
  21. Replies
    33
    Views
    10,001

    I'll be interested to know how this serves you. ...

    I'll be interested to know how this serves you. Hows the noise level?
  22. that story just got crazy. Its hard to feel...

    that story just got crazy. Its hard to feel sorry for the guy.
  23. Replies
    10
    Views
    7,136

    furniture grade plastic wood, oxymoron?

    furniture grade plastic wood, oxymoron?
  24. Search craigslist. Your money will go a lot...

    Search craigslist. Your money will go a lot farther if you know your stuff.
  25. Replies
    13
    Views
    2,640

    I'd say so.

    I'd say so.
Results 1 to 25 of 153
Page 1 of 7 1 2 3 4