Search:

I like regular Titebond because it washes out of my pants, which is where I wipe my finger after spreading the glue :)

In my limited experience the oscillation is an important feature.

It sounds like you have it figured out Justin. That should work fine.

Hi Justin, This isn't what you asked about but is the back side of the cabinet going to have doors or a plywood back? If you have doors all the way around, which is very nice for access, there is...

I still think John is correct Ken. If the bearing is on the template and the cutter is going deeper it must be a slightly larger diameter. (assuming the router isn't tipped, etc.). I guess the...

When I've done drawers in aprons I've ripped the apron board at the at the drawer/apron junction line, cut the drawerfront section out with a simple crosscut, then glued the apron back together. Put...

I agree with Scott here. It will take very little force to pull 1/8 bow out of 5/8" stock over 40" long -- most any attachment method would hold the top reliably flat

I've only done this a couple times but this works: cobble together a plywood box the height of the opening and put it in front of the cabinet. Set the oven on the box turned enough to one side that...

312416
I usually make them as an integral panel to the cabinet, not an add-on. Not all situations allow this method however.312417

For an oven cabinet I construct it without the panel behind it...

No problem at all doing that Justin, I've done it multiple times. Another options you have to make the cabinet a bit deeper than the standard 24". I do that when a countertop abuts the side of the...

Hi Martin,
I haven't figured out how to do it yet. Here's my stop-gap method:
307350
Having to loosen the knob and move the brace every time you want to flip the stop out of the way isn't a...

I have both the Stopstop PCS with the crosscut table and a Grizzly G0623X slider. I wrote a long review comparing the advantages of each but took so long the site logged me off and I lost the text...

Those kinds of cuts scare me also. Depending on how the backer board is mounted you don't really need to have a knife edge. Leave a proud 1/16" flat on the beveled edge so it can register to the...

Hi Keith,
I'm a one man cabinet shop and I needed a second saw--too much time between jumping from rip, crosscut and dado head. When I bought the Grizzly I really wanted a Sawstop but needed a...

Curtis,
I used the 5 cut to set things up, but haven't done it repeatedly after removing and replacing the fence. I just got it last week, so I don't really have long term results to report. I...

Here's a pic. I remembered wrong, this is the only cursor that isn't a magnifier. Buy it's still easy. The scale is etched in the gauge. I suppose you could knock the cursor out of alignment, but...

I don't know what new rails would cost. There is a T slot in the face of the fence you could use to attach a sub-fence

It isn't locked at 90 when you take it off. But the cursor lets you tighten it back down at 90 as you put it back on. It's a magnifier cursor and the lines are fine and exact. It really isn't an...

Ray makes good points and the add-on sliding table won't make your saw a "true" slider, but they are still pretty darn handy. You could avoid cutting the rails by drilling new holes but you would...

I just installed one last Friday. Overall I'm happy, here's my answers:


All seems nice and tight, no play and square cuts.
There are no screws to "take out" in order to remove the slider...

Lot's of good advice here, thanks to all that responded.
Mark

A broad subject I'd like some help with. I will be co-teaching a power tool safety course for our local woodworking club and would like to tap into the Creek's collective wisdom to make sure we...

I've got the Grizzly G9983 open end 15" wide belt sander. I've used the belt cleaning sticks and pads over the years and in the past have been good about rubbing the belt cleaner stick debris off...

That's interesting Frank. The Ceros is small and light, which is what I like about it. The transformer is huge and heavy. Hopefully they won't (or didn't) ruin the sander trying to lose the...

Same here, it allowed me to put it in the cart. I have one I paid full price for and almost went ahead and got another for that price. In my opinion they are orders of magnitude nicer to use than...