Search:

Type: Posts; User: Greg Moore; Keyword(s):

Search: Search took 0.00 seconds.

  1. Replies
    4
    Views
    810

    Take a look at this site: ...

    Take a look at this site: http://www.wwhardware.com/blum-110-176-clip-top-self-close-straight-arm-screw-on-hinge-blumotion-without-blumotion-self-close.html There are several styles and models to...
  2. Thread: Coffee mugs

    by Greg Moore
    Replies
    6
    Views
    1,225

    Remove the screw and place the stainless end over...

    Remove the screw and place the stainless end over something soft (box of rags) and apply compressed air to the screw hole. Insert will fly out of the plastic cover.
  3. Thread: Travel mugs

    by Greg Moore
    Replies
    2
    Views
    877

    This might help. ...

    This might help. http://www.tahoeturner.com/instructi.../coffeemug.pdf
  4. Replies
    11
    Views
    4,711

    I have been using the G0440 for several years in...

    I have been using the G0440 for several years in my one man shop. I used 6" pvc for the main line (24') with some 6" on a couple of drops. I then used 4" from there to the machines. (no grounding...
  5. Replies
    12
    Views
    22,674

    My shop is 28'wide x 36'long x 14' walls. Using...

    My shop is 28'wide x 36'long x 14' walls. Using 2" blanket insulation, covered with OSB. I've been using a 75k BTU Hot Dawg, for the last 7 yrs. I turn the temp down to 45* at night and 62* while...
  6. Replies
    44
    Views
    8,360

    I build custom cabinets to suit the room or the...

    I build custom cabinets to suit the room or the person (height +/-). Depending on the price of hardwoods in your area, some species of wood will be cheaper than others. I find that price spread on...
  7. Replies
    10
    Views
    6,142

    I have used the blum compact 38's on several...

    I have used the blum compact 38's on several projects. 105* opening works in most situations. I use the 107* clip on hinges on most of my frameless cabinets.

    The cheapest source I've found is...
  8. Replies
    47
    Views
    11,869

    I retired just over 7 yrs ago. Just prior to...

    I retired just over 7 yrs ago. Just prior to retirement, I built a new shop and started replacing my weekend commando grade tools (after raising two boys, they were wore out) with higher quality...
  9. Replies
    16
    Views
    2,668

    I originally bought bought the Bosch 1617 EVSPK...

    I originally bought bought the Bosch 1617 EVSPK kit. Later I wanted another motor. I looked around and found a 1617 with a "D" handle base, for the same price as the motor without base. I...
  10. Replies
    2
    Views
    926

    I've been using the Grizzly 2 hp cyclone for...

    I've been using the Grizzly 2 hp cyclone for about 3 yrs. I have the cyclone mounted on the back wall of my shop (28' x 36'). I used 6" pvc for the main run down the center of the shop(10' above...
  11. Replies
    10
    Views
    6,822

    I have used HF 10"x60 tooth blades on my sliding...

    I have used HF 10"x60 tooth blades on my sliding miter saw. I use these blades when cutting prefinished flooring, the aluminum oxide in the finish tears/wears carbide teeth something fierce. I...
Results 1 to 11 of 11