Search:

Type: Posts; User: Jim Ritter; Keyword(s):

Page 1 of 11 1 2 3 4

Search: Search took 0.09 seconds.

  1. Replies
    4
    Views
    506

    Can you drill a hole in the shaft? If so drill a...

    Can you drill a hole in the shaft? If so drill a hole, insert a steel cross pin that then fits in a slot on the pulley. A standard shaft collar slid up against the pulley on the other side locks it...
  2. Replies
    11
    Views
    688

    And yet it is so easy to just "blue" a chisel on...

    And yet it is so easy to just "blue" a chisel on a grinder and the edge is soft and ruined, go figure.
    Jim
  3. Replies
    59
    Views
    9,794

    As Derek said it is quite easy, use a cut off...

    As Derek said it is quite easy, use a cut off wheel. If the screw is held in a vise you can eyeball the vise jaws to center the wheel and visually keep the cut aligned.
    jim
  4. Replies
    23
    Views
    1,825

    If you walk into the store front in Maine you get...

    If you walk into the store front in Maine you get a 10% discount, but then again you get to see and handle, and try out all the tools so you end up buying more!
    Jim
  5. I have a large one mounted on my bench. I often...

    I have a large one mounted on my bench. I often use the four integral dogs, I have on other dog holes lined up with the vise. I also have a #2 clone but it is not mounted to anything yet so I can't...
  6. Thread: Bench Apron

    by Jim Ritter
    Replies
    39
    Views
    2,636

    An apron would not work for me. I clamp down on...

    An apron would not work for me. I clamp down on the front of the bench way too often not to have that convenient edge.
    jim
  7. Thread: It Spins!

    by Jim Ritter
    Replies
    20
    Views
    2,339

    Winton the chain is easily adjusted to have the...

    Winton the chain is easily adjusted to have the jaw parallel at full clamping tension. Once set there is little need to adjust unless you want to clamp something that is out of parallel to begin...
  8. Replies
    20
    Views
    1,391

    I'm pretty sure it was for a screw type holdfast...

    I'm pretty sure it was for a screw type holdfast with a flat bar. The bar kept the screw upright. I've got some old catalogs, I'll take a look when I get to the shop.
    jim
  9. Replies
    13
    Views
    1,622

    Definitely a replacement handle, I have a bunch...

    Definitely a replacement handle, I have a bunch of those handles around the shop. Just got a Bell System axe this summer. Also have a couple braces, a screwdriver and wire cutters. Good tools.
    jim
  10. Replies
    12
    Views
    1,233

    Any chance you can post a photo of the screw at...

    Any chance you can post a photo of the screw at the handle end? We might have some other ideas if we can see what you are working with. You got good advise so far, but there might be others.
    jim
  11. I think Shop Notes did an article about one. I'll...

    I think Shop Notes did an article about one. I'll have to look and see if I can find it.
    Jim

    OK, found it, it is in ShopNotes number 115 page 36. It's well thought out, I wanted to build one when...
  12. Replies
    182
    Views
    33,689

    Very nice Ralph. Was the body cast or made up...

    Very nice Ralph. Was the body cast or made up from plate? Glad to see you are still at it.
    Jim
  13. Replies
    17
    Views
    2,088

    John here are a couple of pics of my real life...

    John here are a couple of pics of my real life tests. Somewhat subjetiive because I didn't have a scale on the handle but these are as I would use the vise. When I read as above where some want the...
  14. Replies
    17
    Views
    2,088

    Please don't use bicycle chain. It is not strong...

    Please don't use bicycle chain. It is not strong enough. If you are making your own use #35 roller chain. I measured upwards of 600 pounds tension depending on the distance from the screw. I've got...
  15. Thread: It Spins!

    by Jim Ritter
    Replies
    20
    Views
    2,339

    Sweet installation Marco, well done. Enjoy it....

    Sweet installation Marco, well done. Enjoy it.
    Jim
  16. Metal Lathes Can't help with info, but it looks like a nice...

    Can't help with info, but it looks like a nice little lathe.
    Jim
  17. I'm guessing you are not married? Jim

    I'm guessing you are not married?
    Jim
  18. Hi Richard of course right after I send you some...

    Hi Richard of course right after I send you some money you ask if I am selling them. No, I'm not selling them. They were the first things I made on my Benchmaster milling machine. I made parts enough...
  19. I made this one one for a swap and couldn't...

    I made this one one for a swap and couldn't decide on the cutter shape so I made a bunch of different ones.
    ...
  20. Replies
    7
    Views
    2,241

    Metal Lathes Any suggestions on disassembling the lathe for...

    Any suggestions on disassembling the lathe for transport? Do I have to cut the flat belt to remove the jack shaft and motor? I'm not sure where to start. The shaper is not following me home. It's...
  21. Replies
    7
    Views
    1,212

    I have more than a couple #3's and they are all...

    I have more than a couple #3's and they are all Stanley's and I did notice a couple months ago when I hung them up that some are different lengths. Not sure how much time I'll have to measure them...
  22. Replies
    17
    Views
    1,859

    That's a sweet sharpener Pete. I too am a...

    That's a sweet sharpener Pete. I too am a draftsman mostly in my former career, but still have my board set up and draw by hand. I would have bought that sharpener over a new one too.
    Jim
  23. Replies
    5
    Views
    634

    Yes Jim the inside edge of the radius is/was...

    Yes Jim the inside edge of the radius is/was sharpened. I'll try and take a better photo this evening.
    Jim
  24. Replies
    5
    Views
    634

    Yes it is like a scorp, cutting and hollowing on...

    Yes it is like a scorp, cutting and hollowing on the pull stroke. The handle is pinned on so it doesn't pull off. That is interesting about the prosthetics but this is much longer than would be...
  25. Replies
    5
    Views
    634

    Tool ID help needed

    I'm doing a basement clean out to help a neighbor dispose of her fathers tools and this was hanging on the wall. Curiosity has gotten the better of me on this one. I can find no makers marks. Here...
Results 1 to 25 of 254
Page 1 of 11 1 2 3 4