Don't underestimate the button battery. Just shorting them can cause them to explode. If they are not in a protective package, store button cells between two pieces of clear packaging tape.
Type: Posts; User: Harvey Schneider; Keyword(s):
Don't underestimate the button battery. Just shorting them can cause them to explode. If they are not in a protective package, store button cells between two pieces of clear packaging tape.
Typically the shank of the drill bit isn't hardened. You will probably have to harden and temper the working end of the tool.
In addition to Steve's comment, I would like to add the following thoughts. A three TPI skip tooth blade clears chip faster and generates less heat, therefore, stays sharp longer. Wandering is often...
Those speed controllers are for universal (brush) motors only. They will not work with induction motors.
Packard carries 3" spindle extenders.
http://www.packardwoodworks.com/Merchant2/merchant.mvc?Screen=CTGY&Store_Code=packard&Category_Code=lathes-acc-spiext
I turn bowls on a Jet 1642 and I agree that 14-1/2" to 15" diameter is a practical size for a finished bowl. I sometimes think that I would like to go larger, but then I can't figure out what I would...
I mounted a tool rack, intended for screw drivers and the like, with two strong magnets. I can store knock out bar, wrenches, and T-handled hex wrenches there. I mounted it to the back side of the...
Wenge is nasty dusty stuff. I posted comments on it recently when I turned a bowl with it. I got a reasonable finish on the piece, but nearly choked on the spray of crumbled wood shavings and dust...
As I have said in another post, I use reverse primarily for sanding. Even for sanding though, it is possible for the chuck or vacuum chuck to unscrew when running in reverse. When I say it is...
I sand the outside of a bowl in reverse at the top so that the dust is thrown away from me and into the dust collector and I sand the inside of the bowl in forward at the bottom of so that the dust...
I just placed an order with "The biggest store on earth" (starts with an A, six letters, ends with an n) for a SuperNova 2 at $150 with free shipping. That's the best price I've seen.
Just thought...
I believe that it is ReStockit.com
Harvey
I am not sure most turners would recognize a small run-out error. It would be noticeable primarily as vibration from the chuck's mass being off axis. Similar to a piece of wood that has a dense...
There is a cedar oil based wood stabilizer that claims to stabilize wood, preventing cracks and minimizing distortion on drying. The product is sold under the name of Turners Choice.
I have used it...
Light from LED's is very directional, so although the total light output may be equivalent, the brightness will be better.
To put it in simple terms, tungsten puts its light out in all directions...
If the lathe is to stay on its wheels, this is a bad idea. Small variations in the floor will cause alignment problems.
If the lathe is to be on its wheels only while being moved, you will have to...
I have the AAW smock and I really like it. I bought it a size larger than I thought that I would need, and I am glad that I did. I want it to keep the chips and dust out of my clothing, but I don't...
If you are looking to save money on a rotary adapter, consider an approach like this:
http://sawmillcreek.org/showthread.php?p=1491842&highlight=adapter#post1491842
I can't comment on the Delta grinder, but there was mention of replacing the wheels.
If you are interested in replacing or upgrading the wheels on a grinder, check out sharpeningsupplies.com. I...
I have the 12" straight rest that came with my Jet 1642, a 6" straight rest and the Delta inside and outsider curves. I use them all and I wouldn't part with any.
The curved rests are wonderful for...
Another possible cause of over-tensioning occurs when the chain is re-tensioned while hot.
As everything cools down, the chain tension increases. This can happen when you go from heavy cutting to...
No matter how strong the tenon, a catch near the rim of a large bowl can yank the bowl right out of the chuck. I know that from personal experience.
Using the tailstock for support will certainly...
Joshua,
For rotating objects there is a phenomenon that is known as critical speed.
A slowly rotating wheel spins around its geometric center. That is the center of rotation based on physical...
DNA dehydrates the wood. It removes most of the water by dilution and leaves alcohol in its place. The alcohol evaporates quickly but the residual water still needs to be removed.
The issue is not...
Thats a great price.
I have had my Airshield for about a year, and I absolutely love it.
Even with two DC pickups, the Airshield is the only way I can walk away from sanding at the lathe without...