Search:

Type: Posts; User: Jack Gaskins; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.03 seconds.

  1. Help drilling angled holes on drill press.

    I have some 2x4s that I need to drill holes in the narrow side along the length of the board at around 2 degree angle. This is for installing conduit pipes in the holes as lumber supports with the...
  2. Replies
    8
    Views
    2,347

    Im actually trying to get more room in my garage...

    Im actually trying to get more room in my garage shop for actual tools and a bench so was looking to store most of my blanks outside and store only small stuff inside. Guess I will have to stick with...
  3. Replies
    8
    Views
    2,347

    Well, I did locate two 48 inch square wood bins...

    Well, I did locate two 48 inch square wood bins about 36 inches tall used to store potatoes or onions in a grocery store. Snagged them off craigslist a few days ago. Put them on concrete blocks on...
  4. Replies
    8
    Views
    2,347

    Show me your wood storage solution.....

    Can you guys post some photos of how you store your turning blanks and other wood in your garage please. I have a lot of turning blanks from 12 inch square down to small 1x1 inch pieces. I am trying...
  5. Replies
    109
    Views
    28,453

    +1 on flannel shirt when woodworking! I wear them...

    +1 on flannel shirt when woodworking! I wear them all freakin year long!
  6. Replies
    39
    Views
    7,376

    Another vote for NOT getting a GO555! Some like...

    Another vote for NOT getting a GO555! Some like them some don't and I am definitely one that does not!
  7. Whatever happened to making a PROTOTYPE first and...

    Whatever happened to making a PROTOTYPE first and actually testing it!! I don't know if Rockler has an R&D office but seems to me they need to actually fly to China and test the product first before...
  8. Replies
    35
    Views
    9,900

    IMO, I would say buy it, tweak it for accuracy...

    IMO, I would say buy it, tweak it for accuracy and use the crap out of it for the first 30 days. If it doesn't meet your expectations, return it, if it take you longer to put it through its paces,...
  9. If it were me.......I would use Evapo rust...

    If it were me.......I would use Evapo rust remover, get it from Autozone. poor on and let set for six or so hours then wipe off. Sand/scuff top wipe off, then go to walmart get a bottle of Barkeepers...
  10. Thanks Rich, I went ahead an got ahold of two...

    Thanks Rich, I went ahead an got ahold of two large countertops and will laminate them together. They already have formica all around. I will order a plate, fence and t-track from Incra.
  11. Is the basic rockler router table with router plate any good?

    Rockler has their router table top and router plate on sale for $99. Does anyone have this top and is it worth the $99?

    Thanks
    Jack
  12. Replies
    9
    Views
    3,453

    Thanks I will take a look for that book. As for...

    Thanks I will take a look for that book. As for the wheels and doors my intent was to up a wheel under each door so the wheel would support the door as it opens. The cabinet wouldn't actually be that...
  13. Replies
    9
    Views
    3,453

    Thanks, so far I have butt joint the plywood and...

    Thanks, so far I have butt joint the plywood and use 2x carcass and attach ply to the 2x or use rabbet and dado. Guess I need to sit down and draw up some plans to see what each option will look...
  14. Replies
    9
    Views
    3,453

    Garage Storage cabinet build question.

    Hello, I need to make a tall storage cabinet for my garage. Cabinet will hold hand power tools; chemicals; small paint cans. I would like to keep the depth around 12-16" so I can see everything...
  15. Replies
    10
    Views
    3,482

    After you get the rust off; use liquid form of...

    After you get the rust off; use liquid form of Bar Keepers Friend. Got mine from Walmart in a squeeze bottle. Works good for removing a lot of the dark stains. I used 220 sandpaper on a mandrel in my...
  16. Replies
    3
    Views
    1,577

    Cast Iron table stain remover

    Most of you may use this stuff to clean your table tops but its new to me......So, I was searching for something to remove stains from my bandsaw table after removing the rust. I have lots of stains...
  17. Thanks Erik, Guess I'll throw on a blade and see...

    Thanks Erik,
    Guess I'll throw on a blade and see how it cuts.
  18. Bought my saw used and the tires were chewed up...

    Bought my saw used and the tires were chewed up something fierce. Looks like the first owner either put the entire blade on the tire so the teeth cut the tires as they spun OR the tension was not...
  19. Replies
    7
    Views
    2,337

    I looked at one of those couple months back at...

    I looked at one of those couple months back at out Menards store and they are VERY bright. Whatever you do,,, DONT LOOK AT THE LIGHT when you turn it on. Took me a few minutes to get the whites spots...
  20. Well, looks like it should work pretty good....

    Well, looks like it should work pretty good. Might have to make a sketch and hang it for future reminder.
  21. Thanks for the link, I will make one for small...

    Thanks for the link, I will make one for small blades. I think I can use a fostner bit to make a recess to fit a block of wood over on the existing guide and the clamping action should hold them on...
  22. Installing bandsaw tires on MM20,,,question.

    Replaced tires on my MM20 and the instructions say to sand the tires after installing. How and why? They don't feel to bumpy to me. For those that have NON Crowned tires do you sand yours?
  23. Yeah ceramic blocks are cool (pun intended) but...

    Yeah ceramic blocks are cool (pun intended) but just don't want to drop that much money on them. Least not now, maybe if the blocks I make don't work out.....
  24. Hi Fred, Well, I purchased my saw used and the...

    Hi Fred, Well, I purchased my saw used and the guides where stiff. After soaking them for 30 days in a bucket of WD40 they turned easier but not much. They are loud and just a PITA. I have read...
  25. My euro guides are large, not sure how to secure...

    My euro guides are large, not sure how to secure the wood in the bearing holder since the euro guides have a threaded end and lock nut. Maybe your idea of making a kerf then using a screw to expand...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4