Just get one of these. They are available in a range of sizes.
Type: Posts; User: Bohdan Drozdowskyj; Keyword(s):
Just get one of these. They are available in a range of sizes.
The longer clip that I have seen shows the woman next to him specifically tell him to use it sideways. He queries her but she insists so I suspect that he was set up.
https://shop.ubeaut.com.au/product/eee-ultra-shine/
https://www.amazon.com/dp/B001F3BCK8
Check what your insurance says about fitting lower rated tyres.
The DW618 2 1/2 HP rating must have originated in the marketing department, at 15A it is only drawing 1 3/4 HP worth of electricity and if you allow for efficiency losses that means that it is a 1 to...
It sounds like the two locations have a transmitter on the same frequency which is jamming your fobs signal and when you move away the fobs signal can then overpower the local transmitter and it all...
Vinegar will attack the clamp metal.
MIG a hex nut directly to the screw. The heat of welding will loosen the screw and it will come out easily.
Put deep scratch on each side of the plate before bending back and forth.
If your motor is delta connected, and the right voltage rating, the VFD goes directly to the motor windings and all of the control (starting/stoping/speed etc) is via the VFD.
I peeled off the clear splinter guards that were coming off at the ends, washed the rail and guard with laquer thinner and reattached them slightly further out on the rail using Nitto double sided...
In my case it was an Italian shaper and the mislabled "brake" pedal was, in fact, the shaft lock. After many accidental steps on the pedal while it was running we disconnected the cable.
We had a...
Westinghouse
Separate frig and freezer, 45 years old.
One gas topup in frig, on its third thermostat but still going strong.
5 moves no problems.
You can't actually ground a PVC pipe as it is an insulator. What you try to achieve is a continuous discharge line to the tool that you are using so that it doesn't become charged up and zap you. If...
When I had some dried waterproof PVA glue on clothing nothing would shift it until I hit it with the primer that is used on PVC plumbing fittings. It didn't disolve it but it made it crumbly so it...
Had a similar problem. Went to an industrial conveyer belt supplier and they made me a new belt out of a piece of offcut that they had lying around.
When I started I used an RO150 with a cheap all plastic shopvac. One day while I was sanding the shop vac burst into flames. The fine dust had blocked the filter and, as the air thru the vac also...
What stops the dog from getting infected?
You don't need much wax on the screws so just draging them flat across a block of wax will leave enough in the threads to lubricate the screw. This is also much more useful as you can keep it in your...
The wet alcohol enters the virus and causes the insides to harden and slowly disintegrate. If you hit it with pure alcohol the outer later is instantly hardened and this prevents the entry of more...
The shock is caused by the buildup of static due to the fast flow of sawdust from your saw thru to the vac. To prevent the buildup Festool supply antistatic hoses with conductive connectors on both...
The collet was tightened without any tool in it. As the nut is screwed down the collet is forced into the taper and reduces in diameter. Without a tool in it the collet reduces enough that it...
I used to buy PVA glue direct from a manufacturer in 44 gal drums. One day their rep was visiting and I mentioned that I had been offered a cheaper glue.
He said "How much do you want to pay?" I...
Use the Parf drill, without the guides, to break the surface, go thru the first layer, on the back after you do the 3 mm holes. Then flip the sheet and finish drilling from the top. This will give...