Search:

Type: Posts; User: Andrew DiLorenzo; Keyword(s):

Page 1 of 4 1 2 3 4

Search: Search took 0.01 seconds.

  1. Make a form to enlarge the pvc to the size...

    Make a form to enlarge the pvc to the size needed.

    Put a large pot of water on a portable heater and boil water. Insert your pipe and get it hot. Oh yeah, figure out how you will hold this hot...
  2. Replies
    48
    Views
    5,291

    Induction is hot quickly. I can put on small pot...

    Induction is hot quickly. I can put on small pot for tea, and before I get the tea bag out, the water is boiling. A convection oven under the range took a little while to adjust to. The fan heats...
  3. Replies
    11
    Views
    2,258

    Hammer flat any 3 or 4 inch piece of copper pipe....

    Hammer flat any 3 or 4 inch piece of copper pipe. Running that against the file will cut grooves that will clean the file.
  4. Replies
    9
    Views
    1,456

    I saw a You tube video of a guy who made a disc...

    I saw a You tube video of a guy who made a disc sander that he mounted on his lathe. For the sandpaper, he used sanding belts that had split apart from age. If I remember correctly, he just glued...
  5. The Long Ranger brand remote selected for the...

    The Long Ranger brand remote selected for the voltage of your DC. Very easy to control.
  6. I like it.

    I like it.
  7. I echo the two lathe solution for your needs. ...

    I echo the two lathe solution for your needs. Avoid that annual transportation nightmare.

    There are two woodworking clubs in Sarasota that I am aware of. Both meet at Advantage Lumber when...
  8. Replies
    13
    Views
    2,823

    Workmates

    Google on over to The Garage Journal (dot com).

    There is a member who has cataloged the history of all the changes to the workmate through the years. Definitely the most complete I've seen...
  9. Replies
    32
    Views
    4,671

    Well, you have a good cord, don't worry about it...

    Well, you have a good cord, don't worry about it and move on and enjoy your saw.
  10. Replies
    25
    Views
    4,600

    You guys are talking about hand planes right? ...

    You guys are talking about hand planes right? Oh, I'm sorry its shotguns, ok.
  11. Replies
    5
    Views
    1,712

    I suggest Rustoleum oil based grey paint or their...

    I suggest Rustoleum oil based grey paint or their silver hammered paint. I have used both on other projects, just be prepared to allow some dry time. The hammered looks closest to the Nova finish...
  12. Replies
    22
    Views
    4,204

    Paul Sellars

    Made several You tube videos (free) of him making a "traditional" bench from high quality plywood. It is aimed at people who need their first bench.

    I understand he has produced some furniture...
  13. Replies
    46
    Views
    6,331

    I have one and can use it. I also have numerous...

    I have one and can use it. I also have numerous TI calculators and have tutored on them to people just learning.
  14. Replies
    9
    Views
    5,443

    You can repurpose a car jack to raise and lower...

    You can repurpose a car jack to raise and lower the table. Either scissors jack or hydraulic jack.
  15. Replies
    14
    Views
    3,570

    I dont know intarsia, but couldn't you cut a thin...

    I dont know intarsia, but couldn't you cut a thin wood piece to the correct shape to fill the gap? Then dye or stain it a contrasting or complimentary color. I am asking.
  16. Replies
    10
    Views
    1,505

    Search on total rainfall map. Lots to pick from.

    Search on total rainfall map. Lots to pick from.
  17. Replies
    9
    Views
    1,889

    A drop of super glue in the center of each joint....

    A drop of super glue in the center of each joint. Then run a bead of wood glue on each side of that. Push joint together by hand for 15 seconds. The super glue acts as a clamp.
  18. Replies
    19
    Views
    2,192

    A watt is one joule per second. There is the...

    A watt is one joule per second. There is the time aspect needed for your analyses, short of going into full dimensional analyses.
  19. If you purchased an aftermarket filter, chances...

    If you purchased an aftermarket filter, chances are they made a sales statement saying how many cubic feet of air flow per square inch or square foot of their filter material. Estimate the air...
  20. I use the same speed almost all the time on my...

    I use the same speed almost all the time on my drill press. I am content to wait a few seconds longer rather than loosening the motor set screw and changing the two belts. That being said, I have...
  21. Replies
    3
    Views
    1,120

    Thanks Dave. I'll see haw many have bylaws...

    Thanks Dave.

    I'll see haw many have bylaws posted on their website, now that I have about a hundred to check!!!
  22. Replies
    3
    Views
    1,120

    Any woodwork club members here?

    I am doing research for Florida Westcoast Woodworkers club and would care to have a link to your website if you have one or a listing of your club name, general location and a copy of your bylaws. ...
  23. Replies
    30
    Views
    5,847

    If your solution to grinding will be to capture...

    If your solution to grinding will be to capture the metal dust, put your strong magnet in a plastic baggie at the collection area. Hold the baggie over a garbage can, open it up, and remove the...
  24. That looks like some solid cast iron on that saw...

    That looks like some solid cast iron on that saw table. Do the cheaper models have that?
  25. I have an older model of this saw, and $750.00 is...

    I have an older model of this saw, and $750.00 is a reasonable price. The unifence is sometimes an after market add on for several hundred dollars. Check if it is single phase or three phase, as...
Results 1 to 25 of 77
Page 1 of 4 1 2 3 4