Search:

I have been asked to build a small end table to match an existing couch. I only have these pictures of the couch frame. Can anyone identify the wood?

I use an older version of this Rockler piece connected to overhead dust collection and attached to the fence of my drill press. It works well for most drilling, but is blocked by very thick pieces...

I run mine through the planer and then sand 60 through 220, followed by mineral oil. I personalize my boards for family and friends by routing in their names, filled in with tinted epoxy.

I just finished this Lean-to Shed. It's 4' x 10', built on cement piers, with the floor and porch made from a deck project cutoffs. It's painted to match our house. The doors are 3' wide and allow...

It will work fine. It was a simple retrofit to attach the SawStop blade cover to the Grizzly splitter on my G091. Just a couple of screws. I run a 4" dust collection hose from the ceiling to the...

I have had good luck stopping at 220, followed by a mixture of mineral oil and melted candle wax. Here's one I made for my Chef sister-in-law. I personalize them by hand routing the name into the...

I built this one out of reclaimed redwood from fence and outdoor projects. It is smaller than you might want but can easily be made larger to accommodate the Egg. It sits outside, uncovered.

I built a short extension at the rear of my table saw. It's a plywood table covered with cheap laminate flooring. It's screwed to the runner at the rear of the saw and held up with angled 2x4s...

Great news! I also have a 2010 G0691 I purchased new and have been watching this thread. Mine is still going strong.

I use these: http://tinyurl.com/Cutting-Board-FeetPrior to screwing them in, I bore a 1/16" deep hole with a forstner bit to hold them I'm place. I like how the board sits at that height. Works...

Your bench looks great. Mine is made out of fir lumber from the big box store. I used cheap laminate flooring to cover the top.It is tough, easy to scrape off glue and paint, and easy to replace. ...

I use these most often. They cost a $1 at the Dollar Store. Cut the brush with scissors to about 1/2 inch. They are silicone construction and dried glue comes off easily. I spread glue with an old...

Here's what I did. The 2x6 stretchers of my work bench have tenons at their ends held in mortises by bolts. It is easy to break down if necessary. The end frames of my bench are glued and pegged...

Happy DW611 owner. I bought and use the dust collection and edge guide accessories.

I used a plastic bin from Target. It is attached to the table on my G0691 with a hinge and foam strips. One side has a hole for air which allows me to reach in and change speeds on the Hitachi...

I bought these, 10 Pack Promark Full Extension Drawer Slide 16" 100 lb rating, for $52 and free shipping, off Amazon. Here's the link: http://tinyurl.com/zggbsa8. They worked great in two dressers...

I'm a very happy Hitachi C12RSH owner. I use mine the same way you intend to use yours. For all the reasons stated above, I bought this saw years ago and sold my Ridgid 12" non slider. Mine is...

My wife had one she was using for scrapbooking. I messed it up so bad, it is now my table, and she bought a new one. The height allows me to sit down and work very comfortably on a project. ...

I saw Tom do it and yelled out loud to my wife how unsafe (for me) it was. I'm a fan of Today's Homeowner. On one show I saw a film clip of a homeowner, an average guy with a low cost contractor...

Here are two I completely recently. Both are approximately 12" x 14". The first is 1.25" thick and the second is 1.5" thick. Both are rock solid. I cut all strips on the table saw before gluing....

Here's my Jim Becker knockoff mounted on my Grizzly G0691. The folding table is an old unused drafting table. The fixed table is plywood covered with cheap laminate flooring trimmed with poplar. It...

Years ago I bought a Genesis brand (clone of many other cheap brands) off Amazon. I think it was under $40 and came with several accessories. It won't die and does a lot of little things: cutting...

Funny thing. The plan was just to put it outside. Now that it has been raining here (finally) quite a bit, I have been keeping it in the garage, where space is at a premium. Even though it is all...

Just finished this BBQ cart with the rule being to use only the wood and materials I had lying around. The top and bottom shelf are made from old deck railings. The frame was made from old fence...

These fittings are expensive. Try looking for businesses which sell used building materials. I have found the great majority of my PVC 4" and 6" fittings, including Ys, 45s, reducers, and couplings...