ALso, forgot to share. I will be using dominos to join
Type: Posts; User: Jason Victory; Keyword(s):
ALso, forgot to share. I will be using dominos to join
It will be a panel with glass. We live in NC so winters can get single digits and summers mainly upper 90’s.
The house was built by a very reputable builder so I’m sure insulation is great. No...
I have been commissioned to build a double front door for a customer. Obviously with front doors one side is usually warm while the other is cold and vise versa. Is there anything special I need to...
Thanks guys, to be honest...unfortunately; it may very well be operator error. I'll give it a shot again tomorrow with some of your tips!
Hey guys I am having problems edge jointing lumber on my delta x5 jointer. No matter what I do it won't edge joint a board, it will always leave about a 16th to a 32nd of an inch gap without clamping...
Anyone have any experience or knowledge on the triton track saw? Seems like a cheaper option to the Festool but can’t seem to find many reviews.
Thanks guys!
Is a worm drive worth the extra $ ?
My old saw just breathed his last, and I need a new one.
I build a lot of tables about 1 a month for clients and I use my circular saw to straight line cut the top edges after glue up. That is...
I guess I should clarify the size. The space that needs to be filled is approx. 6.5”x1.5” so it needs more epoxy that the parallel epoxy mixes that you get at the big box stores.
This isn’t what they wanted at first. They wanted a 48” wide hard maple slab table with a somewhat straight live edge, and the only ones I could find after many calls and searches y’d off on the end...
Do you guys have a 5min brand you like/use?
My lumber supplier that I usually get slabs shipped from sent me this hard maple slab. The plan is to rip down the middle and simply use the two approx 8" pieces as the outer piece, and use normal...
Hey guys, quick question. I am finally deciding that my health is important ;) and thinking about purchasing a Oneida v-3000, and my question is can I run an open duct with a hood on the end to...
Thanks guys! I suppose I should have looked up the products first that probably would of answered the question. Other than the “tilt box II” would you recommend any specific one? Is the wixey a good...
Hey guys so I was thinking about purchasing a saw blade angle gauge and as I was thinking through it I came across a question I wanted to ask. Wouldn’t your table saw need to be perfectly level in...
Hey guys, looking to get upgrade my table saw to a 3hp while doing my best to stay around $1,000. Craigslist has a 1 year old, lightly used, 3hp North State table saw.
After a little research on...
Thanks guys I’ll give it a try!
Hey guys so a couple years ago my uncle got me the hitachi plunge router 2.25hp for Christmas. New out of the box the variable speed knob turned but the speed never went up; it’s simply stuck in low...
I started doing more reasearch on venting outside; and whiles it’s nice to not have to filter I read a lot about sucking your heat/air out of your shop. I’m in NC and we have hot summers and can have...
Thanks I watched the videos they were very helpful.
Last possibility in my mind is when I see the simple/small wall mounted DC that have the motor/blower and bag. The bags I’ve read are prone to...
Hey there Carl I spend 95% of time of table, miter, planer, jointer. I will most likely hook palm sander to shop vac. I was looking at grizzly 2 hp cyclone vs 4 hp canister. My shop will be 20x25.
...
Hey guys I’m currently building a new shop and am looking at a dust collector. Budget is a factor and I have the ability to run the line out of the shop. My question is should I just buy a canister...
Ok what would you suggest to use in order to keep animals such as birds out of the exhaust that also wouldn’t hinder airflow?
I’ve never thought about exhausting it to the outside. Is there a benefit of doing that vs running it into a normal bag setup?
Ok thanks guys! So it sounds like I really need to invest some $ in a good DC system. Unfortunately I am on a budget like most of us I’m sure; should I sacrifice some of my other tools in terms of...