Search:

Type: Posts; User: Dave Verstraete; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.11 seconds.

  1. I'll keep it simple and answer your second...

    I'll keep it simple and answer your second question
    http://www.grizzly.com/products/10-Hybrid-Table-Saw-with-Riving-Knife-Polar-Bear-Series/G0715P

    If you have 240 Volts available...
  2. X2 The old drafting tables had the same material.

    X2 The old drafting tables had the same material.
  3. X3 Welcome to the forum. Contribute and enjoy

    X3 Welcome to the forum. Contribute and enjoy
  4. Replies
    35
    Views
    2,498

    Agree that it was a "cakewalk". That cakewalk...

    Agree that it was a "cakewalk". That cakewalk also saved my life about 10 years ago. They found a precancerous polyp and removed it. After that, I had one every 6 months for 2 years. Then they...
  5. Replies
    11
    Views
    1,743

    Can you shorten the point of the screw an 1/8" on...

    Can you shorten the point of the screw an 1/8" on a belt sander?
  6. Replies
    18
    Views
    1,581

    My first thought when I saw this topic was "Run...

    My first thought when I saw this topic was "Run Forest Run". I attempted to put a doll house kit together once. I am way too fussy to attempt that again. I would make a plan that I was happy with and...
  7. Replies
    6
    Views
    1,537

    General Metalworking The one with the circles might be a magnetic...

    The one with the circles might be a magnetic parallel. It is not magnetic until placed on an electromagnet. Then it transfers the magnetism and is magnetic while the electromagnet ie turned on.
    ...
  8. Replies
    15
    Views
    1,820

    X2 for an 8" Grizzly with a spiral head

    X2 for an 8" Grizzly with a spiral head
  9. Replies
    22
    Views
    2,790

    X2 Spend your money at a local woodworkers store.

    X2 Spend your money at a local woodworkers store.
  10. Replies
    2
    Views
    691

    I've used Carbide Specialties in G.R....

    I've used Carbide Specialties in G.R.
    http://www.carbidespecialties.com/
  11. Replies
    12
    Views
    1,180

    Moses With that history, I think that I would...

    Moses
    With that history, I think that I would take your Dad's shears and either 1: make a collage out of them in a picture frame and hang them in the shop or 2: weld them into a 3D prehistoric...
  12. Poll: Since your initial thoughts on the Grizzly had to...

    Since your initial thoughts on the Grizzly had to do with "finish", you could buy the Grizzly and have an auto body man really jazz it up for you for $500. You'd still be money ahead and have a great...
  13. Like Matt, my 453Z planer is in the basement. The...

    Like Matt, my 453Z planer is in the basement. The struggle was worth it, though.

    Enjoy that new planer. You can now plane highly figured woods without chipping!
  14. Poll: I'll pass also

    I'll pass also
  15. Replies
    201
    Views
    26,703

    Michael I haven't read through all of the...

    Michael
    I haven't read through all of the preceding posts but would just like to put in my 2 cents. I have the 0453 planer with the spiral head and it has served me well. I would buy it again.
  16. Replies
    7
    Views
    967

    A buddy of mine began spray painting the inside...

    A buddy of mine began spray painting the inside of the drum. Needless to say, he lost his eyebrows to the Flash. Luckily, nothing else hurt except his pride.
  17. Woodsmith had a set of plans that my son and I...

    Woodsmith had a set of plans that my son and I used to build a corner desk. I'll check tonite for the plan #
  18. Replies
    39
    Views
    2,695

    X2 to that. On the Great Lakes with a 16' open...

    X2 to that. On the Great Lakes with a 16' open bow boat, you should stay very close to the channel or launch ramp that you came out of. Storms come up very quick and will ruin your day.
  19. Replies
    13
    Views
    1,436

    Moses Have you tried Hickory and Oak Sawmill in...

    Moses
    Have you tried Hickory and Oak Sawmill in Decatur. Nice Guy to work with. Lets you sort through it.
    http://www.hickoryandoak.com/
  20. What's Facebook? :>)

    What's Facebook? :>)
  21. Replies
    15
    Views
    1,054

    Great advice. As an occasional golfer, you should...

    Great advice. As an occasional golfer, you should hit the club that you are most comfortable with. If you are grabbing a 4 iron for the first time that year, put it back in the bag.

    Leave the...
  22. AND filled the filter so full that it had to be...

    AND filled the filter so full that it had to be removed and unclogged:confused: Not that it happened to me, though:eek:
  23. They are not the cheapest but I like a flash...

    They are not the cheapest but I like a flash drive that I can put on my key chain. PNY Half-Hinged. I tend to lose the other ones.
  24. Replies
    11
    Views
    1,018

    The clearance between the blade and the cartridge...

    The clearance between the blade and the cartridge is about the thickness of a nickel. If the lip of that is less than that, it might work.
  25. Replies
    18
    Views
    4,956

    General Metalworking Find a Fabricating shop near you. This one is...

    Find a Fabricating shop near you. This one is across the street from us and cuts aluminum all day long. profabgr.com
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4