Search:

I think I'll look around for some poplar. I like the idea of the first 24" being solid panel. As for the screen part though, I also like the idea of installing the screened section in it's own...

Hello all,
A friend of mine wants me to build her a set of french doors for a bedroom door opening. The bedroom is at the end of a hallway. She wants decorative screen of some sort to be in the...

Timber Products INC. in Medford Oregon, Yreka California, and not sure of the city in Michigan. Columbia plywood in Klamath Falls Oregon.
My Husband manages the one in Yreka. The veneer mill in...

I wonder how much you can heat pvc before you produce toxic fumes?

My leeson 5 hp motor on my Clearvue draws 7 amps with no gates open, 10 to 12 with one or two gates open and 15-16 amps with all the gates open. I have 8 gates total, and I have some leaks from...

Doug,
I don't have any other air filters. I meant if I had settled dust on everything running any kind of fan would stir it up. That's why I like to blast out the shop once a week. I run the...

Doug,
Bill Pentz did an air quality test in my garage a couple of weeks ago, and that is one thing he recommended. I have a similar "garage" set as you, and I work with the door open when...

Jay,
I have the Clearvue, some recycled filters and muffler in a sound board lined closet. I got similar results although your CFM's were little higher that mine. I have a not so ideal duct system...

Jim, Now that is backward:eek: !!!!

But not as backward as mine, I also built a closet , with a double door opening to the front, only I added all the wall,soundboard,...

If I did it over, I'd would have added the wire to the motor and tested it on the bench without the impeller to get the CWW assurance before HEEVing that heavy motor/impeller up on the bracket. But...

Stu,
I don't know if you can see them but there is a plate of cookies on the outfeed table. Bill requested chocolate chip cookies.:D They were goood...
I can't get over how awesome this DC is!!!

Bill Pentz arrived at my shop at 10 am this morning. 48512 First the shop tour where Bill advised many various helpful things regarding dust hoods.48514 The island includes a table saw/with router...

Ok, Ed suggested using slow blow, or "time delayed" fuses. So we installed them and it has been working great since. My husband hooked up an amp meter and it did pull over 100 amp for the first...

Ed, from Cleavue has been patiently working with me, and today he suggested using slow blow fuses. He said these motors pull up to 100 amps on the start-up, and will blow a regular fuse.
So that is...

I have a 110 switch attached to the contactor so I can have a back-up incase I lose the remote. By wiring it direct do you mean not using the remote? When I want to use just the switch have the...

After talking with my husband, he said all the wiring is # 10. So that is good.
I wonder if the closet that the Cyclone is in is too airtight. I haven't installed a vent yet, but there was a lot...

48367 Here is another one.
Don, I didn't get your PM yet.
Thanks again!

48366 There! I did it :cool:

OK Don please PM me with your cell phone number, since I can't seem to get this picture thing right!!

The wiring was done to code, according to an electrical contractor. I am just ignorant on...

Ok, So I have a section of #12 wiring (about 2 ft)that goes from the motor to the circuit breaker. It is a piece of wiring that was originally was used for a dryer outlet for the garage. (Maybe it...

The DC is a 5 HP Clearvue, and is wired to a 30 amp circuit breaker, and yes the ducting is installed. Do you think I should start the DC with all the blast gates closed? I will try in included pics...

Hi all,
Finally got the Clearvue fired up last night. All I can say it WOW!!! I am jazzed! It ran beautifully 10 or so times last night and today, but it has blown two set of fuses today. I...

Wow Paul! How inspiring! I have been working on my "island" which includes TS, router station, outfeed and downdraft. I have everything ducted to the main DC cyclone. I have been pondering whether...

Don and Bill,
You could use my shop, I am in the final stages of installing the Clearvue. I live in Yreka CA. It is about 4 hours north Sac. I am hoping to be done with ducting and wiring in the...

I bought a Clearvue, built a closet around it for my garage turned full time shop,and am real close to getting it fired up. Waiting on the electrician. I have been working on all the dust ports and...