Search:

Type: Posts; User: Darrin Vanden Bosch; Keyword(s):

Page 1 of 3 1 2 3

Search: Search took 0.01 seconds.

  1. It boils down to, what size wire was used to feed...

    It boils down to, what size wire was used to feed this panel. The breaker is there to protect the wire so it NEEDS to be sized properly to insure the load isn't too much. If the load is too much it...
  2. Replies
    63
    Views
    7,127

    How many amp service are you planning on for your...

    How many amp service are you planning on for your shop? If it's a 100 amp service then 4 gage will not do.
  3. Replies
    34
    Views
    14,209

    Three words, Tried and true. This is a natural...

    Three words, Tried and true. This is a natural oil finish that is very easy to apply, get consistent results and is NON-toxic, with NO-VOC's, (this is NOT a water-based finish), I use 4-6 coats wiped...
  4. As you can see, many here think this is ok as...

    As you can see, many here think this is ok as long as this is "accessible" in the attic. While it may technically be accessible, it is just not a good idea. Common sense should tell you this is not...
  5. Replies
    24
    Views
    5,937

    I get mine at lowes or hd, exactly what you...

    I get mine at lowes or hd, exactly what you described.
  6. For years I have been using a few of those...

    For years I have been using a few of those gorilla racks that Costco sell and have them stuffed full, they have worked out very well. I also have a few sets of saw horses that have been piled on for...
  7. They real question is....why on earth did they do...

    They real question is....why on earth did they do that? Is this for the alcoholic cat?
  8. Replies
    9
    Views
    3,420

    Its so clean I can't even see a picture of it

    Its so clean I can't even see a picture of it
  9. Replies
    15
    Views
    2,927

    Yes biscuits would be strong enough, double them...

    Yes biscuits would be strong enough, double them up. It would be best to not move your workbench around though as the pushing and pulling will put stresses on those same joints. I do agree M&T would...
  10. If you're going to just strap it to the bottom of...

    If you're going to just strap it to the bottom of the joists put in conduit, at least 1" maybe 1 1/4 ". It will not hurt the wire and properly sized conduit will have enough airspace, you just don't...
  11. EMT pipe, conduit

    EMT pipe, conduit
  12. Make a properly sized EMT runner across the...

    Make a properly sized EMT runner across the ceiling, it will protect the wire in the long run.
  13. Replies
    17
    Views
    4,193

    No disresect but, Where do you live, cuz that is...

    No disresect but, Where do you live, cuz that is definitely excessive. Do it yourself and save 3/4 of that quote. If you're not sure about wiring the panels you can get an electricain to do it for...
  14. Replies
    31
    Views
    25,326

    Check with your local inspector

    Check with your local inspector
  15. Replies
    2
    Views
    1,153

    Its basically $10 a board foot, if it has very...

    Its basically $10 a board foot, if it has very good figure then it should be worth it. If it doesn't then don't waste your time. I am normally paying 6-7 a bd. foot, but I'm also digging through...
  16. I believe sapele is actually in the magnolia...

    I believe sapele is actually in the magnolia family, i dont know the scientific names so take it for what its worth.
  17. I've done a lot of construction over the years...

    I've done a lot of construction over the years and ridgid conduit just looks better, it looks like you cared about what you are doing. Flex does not give that look, it looks like you don't care and...
  18. It'll never see a car......until the wife tells...

    It'll never see a car......until the wife tells you otherwise.
  19. Replies
    16
    Views
    3,315

    That is friggin ingenious

    That is friggin ingenious
  20. Replies
    4
    Views
    1,375

    Shipping

    I am looking for a reasonably prices shipper to ship something to a client. I would like a blanket wrapped service that is reliable, friendly and can be ready in a short time if need be. This piece...
  21. Replies
    17
    Views
    2,839

    Irregardless of the weight factor times four, if...

    Irregardless of the weight factor times four, if you're worried about it, replace it with something stronger. It's all about piece of mind!
  22. Replies
    6
    Views
    1,289

    I've been using both exotics and domestics for...

    I've been using both exotics and domestics for years, many years, and the only thing I have a reaction to is oak which turns out is ok since I really don't care for it anyway.
  23. Multimeters need to be calibrated every so often....

    Multimeters need to be calibrated every so often. This is what this sounds like. If it was accurate you'd have a lot of fried electronics in the house.
  24. Replies
    14
    Views
    3,006

    Its for your dad, splurge, he's worth it isn't...

    Its for your dad, splurge, he's worth it isn't he. Take it from someone that no longer can make something for dad.
    Darrin
  25. Replies
    22
    Views
    3,239

    When I started out all I had was my dads RAS,...

    When I started out all I had was my dads RAS, early 60s edition, not something I really liked ripping wood on. When I restarted woodworking all I had was a craftsmen TS with the flex drive and then...
Results 1 to 25 of 74
Page 1 of 3 1 2 3