Search:

Type: Posts; User: Mark Waltrip; Keyword(s):

Search: Search took 0.00 seconds.

  1. Replies
    4
    Views
    1,582

    You're looking for Extra Length Aircraft Drill...

    You're looking for Extra Length Aircraft Drill Bits. ;)
  2. So even under controlled conditions the wood will...

    So even under controlled conditions the wood will still crack?

    The reason I ask is because I have a neighbor who has a "drying shed" for 'wet' wood, and could use it for this purpose if I asked....
  3. Oak End Tables from my own harvested trees.

    I'm new to woodworking and am learning as I go, so please bear with me.

    I am going to be cutting down a 60' Red Oak next week that I've been planning on harvesting for lumber. The wife took one...
  4. Wood Lathe and Machine Drill Chuck Problems.

    Lathe: Jet JWL-1236 Woodworkers lathe
    Headstock & Tailstock Taper: MT-2
    Drill Chuck Taper: 2JT
    Drill Chuck: Jacobs 14442 w/ 2JT taper


    OK, so I bought a drill chuck to go with my wood...
  5. Replies
    5
    Views
    1,569

    Lathe and Drill Chuck Problems

    Lathe: Jet JWL-1236
    Headstock & Tailstock Taper: MT-2
    Drill Chuck Taper: 2JT
    Drill Chuck: Jacobs 14442 w/ 2JT taper

    OK, so I bought a drill chuck to go with my wood lathe, an adapter that...
  6. Replies
    10
    Views
    1,829

    Thanks for all of the help everyone. My main...

    Thanks for all of the help everyone.

    My main concern was thinking that I had a defective unit, but from the reports here it is normal for the pivoting head models.

    Thanks for the help.
  7. Replies
    8
    Views
    5,810

    X2 Like you, I am very inexperienced in...

    X2

    Like you, I am very inexperienced in turning as well, and the great people on this forum have been a great help thus far.

    I bought the "Woodriver" 4-Jaw chuck from Woodcraft this past...
  8. Replies
    10
    Views
    1,829

    New Lathe Question .... Jet JWL1236

    I just started working with my new lathe, and in tinkering around I found a few problems. Could someone please shine some light on the issue for me?

    The main issue I have is as follows ....

    I...
  9. Replies
    13
    Views
    63,253

    Finding 'Dead Center' on Dowel Rod?

    I've been struggling with ways to find dead center on pieces of round dowel rods, and didn't know if any of you have any suggestions?

    I'm having problems both with finding dead center on a piece...
  10. OK. Here's the problem I've run into. I will...

    OK. Here's the problem I've run into.

    I will not only be turning wood, but I will also be turning small diameter copper round rod. The main diameters I will be turning will be 3/4", 1", and 1...
  11. Still Looking For A Good Chuck .... Please Help

    I'm still looking for a good chuck, and I tend to over analyze things. That's probably 90% of the reason I haven't purchased one yet. I've seen all of the Teknatool chucks over at the local...
  12. Replies
    14
    Views
    1,930

    I'm new here, but I HAVE worked with woods before...

    I'm new here, but I HAVE worked with woods before that are highly allergenic. Another hobby of mine is flintknapping, and I make reproductions of Native American knives out of stone and antler, or...
  13. Replies
    12
    Views
    2,018

    Rookie Question.

    I'm sorry that I'm bothering you all with my rookie questions, but I need a little advice since I'm brand new to turning and don't have anyone locally to help. I've been wanting to learn how to turn...
  14. Replies
    9
    Views
    1,420

    I'm sorry, but I forgot to specify what I'd be...

    I'm sorry, but I forgot to specify what I'd be using the chuck for. That's my fault.

    On some of the brass and copper stock I will be turning the end and rounding it off using a file or similar...
  15. Replies
    9
    Views
    1,420

    Which Chuck to buy?

    There are so many choices out there for lathe chucks, and since I am new to turning could someone please give me some advice on the applications I will be using it for?

    I have a Jet jwl-1236 lathe...
Results 1 to 15 of 15